Make | Model | Problem | Solution | Date |
| | | |
Found: 84
|
B & O | 5102 77XX | Intermittent negative picture. | Dry joints on i.f. board connector , in vision detect can. | 14-09-04 |
B & O | 5102 77XX | Negative picture - intermittently. | Drys on IF edge connector , & earthg lugs in vision can. | 14-09-04 |
|
Cascade | TV510 | BLOWS LINE OP TRANSISTOR AT SWITCH ON | VR901 , ZD901 , ZD902 | 14-09-04 |
Cascade | TV510 | Blows LOPTr at or shortly aft sw on | HT supply high until warmed up (should be 112v) - VR901 HT pot | 14-09-04 |
Cascade | TV510 | St/by only | HT at lop tr = 125v (112v); C909 47µ 63v, R414 12R 2w o/c; ZD401 12v zener s/c | 14-09-04 |
Finlux | 5100 | No sound/pic - EHT present | Blank raster when A1s advanced - no S5v or S12v supplies - Ta 18 BC557 leaky | 14-09-04 |
Grundig | 1510 | Dead - intermittent. | Crack in print. | 14-09-04 |
Grundig | 1510B | Sound - intermittent or no sound. | Poor joints on speaker wires. | 14-09-04 |
Grundig | 1510GB | Dead. | C863 leaky. | 14-09-04 |
Grundig | 1510GB | Intermittent or no colour. | R587. | 14-09-04 |
Hitachi | C32W510SN A7 | Cuts out int | Check earth links & reg heatsinks for dry joints | 14-09-04 |
Hitachi | C32W510SN A7 | Field faulty - jittery & lines below centre - tappable | Dry joints R602 & 3 connected to pin 5 IC601 (under glue & a plastic strut) | 14-09-04 |
Hitachi | C32W510SN-311 | Dead with st/by led pulsing | IC4000 TDA7263M Audio o/p chip s/c | 14-09-04 |
Philips | L01.1 28PT5107 | 1cm noise band from top to bottom lH side of screen varies with brightness & chan | D6460 BY 228 over LOPTx | 14-09-04 |
Proline | 5100RC | No pic - field coll noticed when A1 advanced, sound ok | Replace o/c 0R22 fusible resistor (R433) feeding
the frame chip. The Frame output chip was O.K. | 14-09-04 |
Samsung | CI5102Z | NO SIGNALS , TUNE VOLTS VARY BUT NO STATIONS | CHECK RQ04 , 05 , DZ824 33v 05 10k 0.25W | 14-09-04 |
Sanyo | CTP5101 | No picture - sound ok. | R617 ( 330k ) o/c. | 14-09-04 |
Sanyo | CTP5103 | East west - bowing out. | Change C451 ( 330u F ) & try C455 ( 330nF ) & C456 ( 180nF ) | 14-09-04 |
Sanyo | CTP5103 | Frame reduced - 3" at centre. | C451 ( 330u f , 10v ) leaky. | 14-09-04 |
Sanyo | CTP5103 | Frame rolling. | D201 leaky. | 14-09-04 |
Sharp | Deco 4 DV5105/DV5107 | dead, no PSU output, R705 burnt | IC700 TEA1039 pin 9 leaky to pin 7, R705 3k3 0.5W fusible (RRXZ0242BMZZ), also check D705 1N4148 and Q701 BC635 | 14-09-04 |
Sharp | Deco 4 DV5105/DV5107 | won't come on from stby when remote is used, green and red LEDs flash. But it would come on Ok when mains switch is used. | R751 0.33R o/c | 14-09-04 |
|
Sharp | DECO4 DV5105H | Trips at sw on then comes back on but trips again on chan change | R716 0R22 in psu gone slightly hi | 14-09-04 |
Sharp | DV5101 | No st/by | Chopper tfmr hi res on 5v winding | 14-09-04 |
Sharp | DV5101 DV5103 | Stuck in StBy : Pic distortion : White pic : No OS | All can be caused by IC1404 TVPO replace PtN RHIX1443BMN5 | 14-09-04 |
Sharp | DV5101 DV5103 | Stuck in StBy: No vertical drive: Colour faults: D | All can be caused by IC1400 VSP replace PtN RHIX426BMZZ | 14-09-04 |
Sharp | DV5101H | Dead maybe smell of burning D708 s/c R705 o/c | Sharp issue repair kit | 14-09-04 |
Sharp | DV5101H | Dead with smell of burning | R705 overheating - D708 s/c | 14-09-04 |
Sharp | DV5101H | St/by only | HT high at 170v (113v), Opto CNX82A faulty but still no go - link 147 in 25v line was o/c (an inductor) fitted wire link in lieu & now ok | 14-09-04 |
Sharp | DV5101H | WONT COME OUT OF SBY | R612 OPEN - CHANGE R612 WITH 2.2ohm AND FIT R612 2.2ohm Sharp -XZ0204BMZZ , J-13 1.2ohm Sharp VRD-RA2HD1R2J | 14-09-04 |