| Make | Model | Problem | Solution | Date |
| | | |
| Found: 210
|
| B & O | 31/63 | Int reverts to st/by | Dry joints on conns between 2 psu pcbs - check elect caps also | 14-09-04 |
| Beko | 116328NX | Blank grey raster with white line at top | R815 22R in 16v supply o/c as C712 4µ7 hi esr also C811 220µ hi esr (16v supply line had risen to 29v) | 14-09-04 |
| Beko | 16326NX | Dead/st/by only or partial line coll | C805 330nF 400v dry joints or burnt | 14-09-04 |
| Beko | 16328 | dead | s/c lopt use HR7218 | 14-09-04 |
| Beko | 16328NTX | Blank raster with EHT present | Dry joints T104 5v reg | 14-09-04 |
| Beko | 16328NX | Blank red raster - sound ok | No volts coll T1205 - R1215 22k 1w on crt base | 14-09-04 |
| Beko | 16328NX | Dead aft LOPTx changed | Micro SDA20563A516 faulty | 14-09-04 |
| Beko | 16328NX | Keeps auto tuning to same chan | R61 27k 2w o/c - feeds 30v zener from 200v supply | 14-09-04 |
| Beko | 16328NX | No front panel control - r/c ok | Child lock on - to remove hold "+" & "-" buttons whilst sw on tv | 14-09-04 |
| Beko | 16328NX | No mono sound | Faulty IF can - pt no BEKO63S140 | 14-09-04 |
|
|
| Beko | 16328NX | No pic unless A1 increased, then same again next time sw on | IC501 TDA4680 | 14-09-04 |
| Beko | 16328NX | poor field lin | R717 1M hi res | 14-09-04 |
| Blaupunkt | 63-39VT | CRT goes to full brightness then the set goes to st/by | R793 ( 470R) crt base & change TEA 5101 .( Measures s/c pin 5 to GND on TEA ) | 14-09-04 |
| Blaupunkt | IM63-18FM 100-41 | E-W bowing - won't correct | IC555 TDA 8145 | 14-09-04 |
| Blaupunkt | IM63-18FM 100-41 | Width excessive | D518 BY 399 s/c
| 14-09-04 |
| Blaupunkt | IS63-31 | No col | IC 5080 TDA 4650 colour decoder faulty | 14-09-04 |
| Bush | 2063NTX | Field collapse | C701 4n7 leaky | 14-09-04 |
| Bush | 2063NTX/A | Dead | s/c BUZ90A o/c 330 K ( R805 ) | 14-09-04 |
| Bush | 2163NTX | Dead with smoke | R809 0R47 fusible burnt; s/c chopper tfmr | 14-09-04 |
| Bush | 2163NTXA | Int sound | caused by bad joints UL302 coill near TDA2546 on Nicam pcb | 14-09-04 |
| Bush | 2863NTX | Field collapse | 33v supply missing - R818 33k o/c | 14-09-04 |
| Bush | 2863NTX | Field collapse | No ramp sig pin 42 of TDA8362. R818 22k 1w o/c | 14-09-04 |
| Bush | 2863NTX | int switches between mono & stereo | can be tuner low spec - ?40 CPC | 14-09-04 |
| Bush | 2863NTX 11AK19 | Dead - LOPTr s/c | When replaced runs hot with bottom cogging - dry joint on link J613 | 14-09-04 |
| Bush | 2863NTX 11AK19E3 | Dead with HT of 16v - ok on dummy load | Supply to 5v reg missing - R867 0R33 o/c | 14-09-04 |
| Bush | 3463NTX 4400 | No sound/pic - no 5v | TP6 BD441 | 14-09-04 |
| Bush | BC6318 | No or intermittent sound. | Dry joint from 1Z7. | 14-09-04 |
| Bush | BC6338 | Channel selector stuck on prog. | ET6016 , 1R1106. | 14-09-04 |
| Bush | BC6338 | Tuning - no channel change. | ET6016 &/or 1R1106 | 14-09-04 |
| Bush | BC6348 | Dead | 4D14 | 14-09-04 |