| Make | Model | Problem | Solution | Date |
| | | |
| Found: 57
|
| Aiwa | CXZR800K | At sw on relay clicks "DEMO" displayed then dead - keeps repeating | Check 2 x 2SK2723 FETs on sound o/p heatsink | 14-09-04 |
| Alba | CTV4800 | No sound | Q201 2SC2703 faulty, TDA1904 audio chip faulty | 14-09-04 |
| B & O | LX2800 | Blank raster & no sound - OSD OK | C18 on decoder board dry joint | 14-09-04 |
| B & O | LX2800 37XX | Sync - poor sync. | 26IC5 ( TDA1940 ) | 14-09-04 |
| Goodmans | SD1800 | CHILDLOCK | PRESS "STANDBY" AND "SYSTEM" TOGETHER | 14-09-04 |
| Grundig | CUC2800 | Arcing from LOPTx former to adjacent components | Tripler faulty | 14-09-04 |
| Grundig | CUC2800 | Dead - psu working ok | Relay contacts | 14-09-04 |
| Grundig | CUC2800 | No sound | Check TDA6200 sound proc & U2829B sound dem chip | 14-09-04 |
| Grundig | CUC2800 | Sound from one chan only & no brill adj | Micro SDA2011-A005 faulty | 14-09-04 |
| Grundig | CUC2800 | Sound low & dist | U2829B IC sound chip | 14-09-04 |
|
|
| Grundig | CUC2800 | The tripler had failed. After replacing it the set | Microcontroller chip type SDA2011 -AOO5 . Make sure that you get the right one for the set. | 14-09-04 |
| Grundig | CUC3800 | Dark on left, bright on RH side | C2582 1µ faulty - lum signal decoupler to pin 15 TDA3505 chip | 14-09-04 |
| Grundig | CUC3800 | EW fault aft tripler replacement | R571 4R7 & IC555 E/W chip | 14-09-04 |
| Grundig | CUC3800 | Int switches to SECAM . | C507 100uF 25v. Connects to pin 2 TDA8140 line drive IC. | 14-09-04 |
| Grundig | CUC3800 | No sound | IC2210 U2829B - fit same type as replacement | 14-09-04 |
| Grundig | CUC3800 | No sound - just hiss | IC2110 U2829B sound IF demod chip on sound IF stereo board | 14-09-04 |
| Grundig | CUC3800 | No sound - multistandard TV on wrong setting | On front panel press"N", select 0,1,2,3 or 4 with P+/- buttons. Each no. refers to a different std. Press "M" to store | 14-09-04 |
| Grundig | CUC3800 | PICTURE DARK ON LEFT HAND SIDE BRIGHT ON RH SIDE | C2582 1uF ON PIN 15 TDA3505 DRIED UP AND OC | 14-09-04 |
| ITT | CMR800 CMR800 | Weak / distorted sound. | C228 ( 100uf , 16v ) in CMR IF. | 14-09-04 |
| ITT | CMR800/3 CMR800/3 | No Sound. | Check pin 11/12/9 for 11.5v. If missing IC202 TDA1035T. | 14-09-04 |
| ITT | CMR800/3 CMR800/3 | Weak Field sync. | If ok on weak signal Change C209 ( 100uF ) | 14-09-04 |
| ITT | CVC800 | Dead | HT almost 300v on LOP Tr coll - BU126 chopper tr leaky e-c | 14-09-04 |
| ITT | CVC800 | Dead. | C757 o/c low 110v rail. | 14-09-04 |
| ITT | CVC800 | No field sync | 100µ cap next to SAWF in CMR800 | 14-09-04 |
| ITT | CVC800 | Snowy pic | 1st RF Amp BF960 in CMR800 faulty | 14-09-04 |
| ITT | CVC800 | Startup - Intermittent start up. | C757 ( 10u F ) | 14-09-04 |
| ITT | CVC800 | Startup - will not start from cold. | R744 ( 100k ) . | 14-09-04 |
| ITT | CVC800 | Startup - will not start from cold. | R731 ( 820k ) high. | 14-09-04 |
| Loewe | MS56 C8001 | Stuck in standby. | R534 ( 3.3R ) o/c , T534 , C534 ( 47uf ) | 14-09-04 |
| Loewe Opta | C8000 | WHISTLES + HIGH HT | C638 | 14-09-04 |