| Make | Model | Problem | Solution | Date |
| | | |
| Found: 171
|
| Alba | CTV6682 | Blank raster | TDA8362A in prot mode - C707 in field fback volts supply | 14-09-04 |
| Alba | CTV6682 | Field coll & no sound | No volts at ramp gen pin 43 TDA8362A; R818 22k o/c | 14-09-04 |
| Alba | CTV6682 | Field collapse | R181 22k in 33v supply gone hi | 14-09-04 |
| Alba | CTV6682 | Int then dead | chopper tfmr dry joints | 14-09-04 |
| Alba | CTV6682 11AK12 | green flyback lines can be seen on the picture, otherwise is Okish | no green output from TDA8362A(2Y), the IC is u/s - caused by intermittently arcing LOPTx (HR6465). | 14-09-04 |
| Bush | 2820T | Line pulling, tearing or bent verts - lack of width | C827 47µ 160v HT res cap | 14-09-04 |
| Bush | A823 | Frame - linearity poor - drifts. | 5C35 ( 250PUT ) | 14-09-04 |
| Bush | A823 | Frame Line Varies After Set Is Warmed Up | Check 5C35 | 14-09-04 |
| Bush | A823 | Sound - buzz/crack when warmed up. | 3C2 , 3C17 ( 50uf ) | 14-09-04 |
| Bush | A823A | AFC Problems | 1VT5 | 14-09-04 |
|
|
| Bush | A823A | No or Intermittent sound. | Dry joint on 1Z7. | 14-09-04 |
| Bush | A823AV | Int on channel change. | 3C2 , 3C17 ( 50uf ) . | 14-09-04 |
| Bush | A823AV | Tuning - AFC. | 1VT5. | 14-09-04 |
| Contec | KT8250 | dead - chan display and relay click present | R504 330k in psu o/c | 14-09-04 |
| Daewoo | DVT1482P | Dead | F4AH fuse o/c, chopper tr 2SD2499 s/c - used 2SD1555 in lieu, C811 100µ 16v hi esr, 220µ 25v hi esr | 14-09-04 |
| Daewoo | DVT1482P | Dead - mains fuse blackened & Chopper Tr s/c | TDA4601 control chip & C811 100µ 35v | 14-09-04 |
| Daewoo | DVT1482P | Dead with burning smell | LOPTx | 14-09-04 |
| Daewoo | DVT1482P CP310 | Sound absent in TV mode - ok in pback | Check RHS edge connector for dry joints/damaged print on video unit | 14-09-04 |
| Daewoo | DVT2082P | Int dead | Dry joint C817 100µ - remove plastic strut to see | 14-09-04 |
| Daewoo | DVT2082P | Red missing | Q552 2SA1266 on crt base | 14-09-04 |
| Daewoo | GB5582TX | Pick fades out maybe once a week | Dry joints LOPTx heater pin | 14-09-04 |
| Ferguson | TX90 (TDA8214) | Picture distorted on top, incorrect linearity, horizontal line 5cm from top.Color Flickering. | Check replace DL15,=33V zener. Check also DL03 | 14-09-04 |
| Ferguson | TX90 (TDA8218) | White raster with retrace lines visible..When hot, pink raster with normal OSD.Sandcastle not ok. | SMD resistor RL03 open circuit. | 14-09-04 |
| Ferguson | TX90 (TDA8218) | White raster with retrace lines visible..When hot, pink raster with normal OSD.Sandcastle not ok. | SMD resistor RL03 open circuit. | 14-09-04 |
| Ferguson | TX90(TDA8214) | Picture distorted on top, incorrect linearity, horizontal line 5cm from top.Color Flickering. | Check replace DL15,=33V zener. Check also DL03 | 14-09-04 |
| Goodmans | W282NS | Width lacking with foldover | D25 BA157 | 14-09-04 |
| Grundig | 8240 | Lack of blue. | R1958 o/c. | 14-09-04 |
| Grundig | CUC1822 | Hor dashed magenta lines superimposed on pic | Check for dry joints/elect caps in "feature" box | 14-09-04 |
| Grundig | CUC1882 | EHT comes up at sw on then reverts to st/by | Dry joint at fop scan coil plug in middle of pcb | 14-09-04 |
| Grundig | M82-100IDTV | Tripping - stops if tripler dis'd | Check caps in psu control sub panel for low capacitance | 14-09-04 |