Make | Model | Problem | Solution | Date |
| | | |
Found: 55
|
Ferguson | A51F | NO CONTRAST | REPLACE RL05 | 14-09-04 |
Ferguson | A51F | No contrast | RL05 o/c | 14-09-04 |
|
Ferguson | A51F | PICTURE BREAKING UP, CRACKLING NOISE | REPLACE LOPTX/FOCUS UNIT | 14-09-04 |
Ferguson | A51F | Tripping | Field IC & TV92 BC848 sm | 14-09-04 |
Ferguson | A51N | Distorted sound | C131 10µ 16v in IF can | 14-09-04 |
Ferguson | IKC2 A51F | Dead - LED flickers twice briefly | LOPTx | 14-09-04 |
Ferguson | IKC2 A51F | Sound low | Weak audio o/p at pin 10 IF can, CS14 1µ 63v in the can low cap | 14-09-04 |
Ferguson | IKC2 A51F | Tuning mode | press and hold the PROG button in for a few seconds B4 it displays the on screen graphics. To unskip channels; display the tuned station by pressing PROG for a few seconds and then press the red fasttext button to store. | 14-09-04 |
Sharp | 5BSA 51AT15 | Dead symptoms with psu running | No line drive base Q603, no 5v supply pin 8 EEPROM IC1002 as 5v reg tr Q704 BC338-40 o/c emitter | 14-09-04 |
Sharp | 5BSA 51AT15H | appears dead, LED is green | Q704 BC338 o/s | 14-09-04 |
Sharp | 5BSA 51AT15H | Corrupted service mode settings after replacement of Q601/2 | No stopping when tuning, height and vert posn out - set AFC optione byte to '9F' | 14-09-04 |
Sharp | 5BSA 51AT15H | Dead | LOPTr, Q509, Q510 & C713 | 14-09-04 |
Sharp | 5BSA 51AT15H | Dead | C713 1000µ 25v hi esr caused failure of Q509 BC635 & Q510 BC338 in field cct | 14-09-04 |
Sharp | 5BSA 51AT15H | Dead | C716 100µ hi esr | 14-09-04 |
Sharp | 5BSA 51AT15H | dead | Q601 BU508DFI s/c (use correct type) | 14-09-04 |
Sharp | 5BSA 51AT15H | dead | LOPTr reads s/c in situ, check R622 - one of its ends shorting to earth print | 14-09-04 |
Sharp | 5BSA 51AT15H | Dead - LOPTr BU508DF1 blown | When Tr replaced , overheats due to leaky line dr Tr Q602 BC635 - fitted BC639 in lieu (checks ok out of cct) | 14-09-04 |
Sharp | 5BSA 51AT15H | Dead - no LED | caps in psu sec plus BU508DF1 & 2SC335-19 dr tr - NOTE MUST use correct replacements or will not work properly IE brushing if dr tr incorrect | 14-09-04 |
Sharp | 5BSA 51AT15H | Dead - no start up | C713 1000µ 25v hi esr & Q601 BU508DF1 LOP tr s/c | 14-09-04 |
Sharp | 5BSA 51AT15H | Dead BU508DF1 LOPTr s/c | Replaced with BU2508DF - given as equiv but DOES NOT work! Use correct Tr & replace C713 1000µ hi esr | 14-09-04 |
Sharp | 5BSA 51AT15H | Dead st/by only | No line drive from MC44007 ic; 5v supply ok in st/by but dropped when sw on - BC338-40 tr cooked up | 14-09-04 |
SHARP | 5BSA 51AT15H | DEAD WITH GREEN LED | CHECK Q704 BC338 | 14-09-04 |
|
Sharp | 5BSA 51AT15H | dead, no LED, HT is Ok | no 5V supply to jungle IC, Q708 BC338 u/s (RHTX0102BMZZ) | 14-09-04 |
Sharp | 5BSA 51AT15H | Field collapse/ R & G lines at top of pic | BC636 in FOP stage causes field coll & D504 1N4148 causes lines | 14-09-04 |
Sharp | 5BSA 51AT15H | field cramp, no OSD, no vol adjust | Q510 BC338 | 14-09-04 |
Sharp | 5BSA 51AT15H | Field foldover & no R/C or local control | Q509[BC635] and Q510[BC338] | 14-09-04 |
Sharp | 5BSA 51AT15H | Green LED flashes and dim - no sound/pic | HT = 113v (should be 105v); Q708 (BC338-40) and D715 (5v1 zener). | 14-09-04 |
Sharp | 5BSA 51AT15H | HT high at 114v (105v) & EHT varying (can blow BU508DFI (don't fit BU508DF) | ZD717 & 718, Q708 (7v supply) faulty | 14-09-04 |
Sharp | 5BSA 51AT15H | Int cuts out | HT ok, 5volt supply +5Vb low Q708 BC338-40 u/s | 14-09-04 |
Sharp | 5BSA 51AT15H | Int loss sound and/or colour for 1sec . | Change C209 from 1uF to 100nF 50v Pt No VCEAGA1HW104M , C808 from 100nF to 47nF 50v Pt No VCKYTV1HB473K ( use only Sharp part | 14-09-04 |