| Make | Model | Problem | Solution | Date |
| | | |
| Found: 25
|
| Sony | BE-3B | int no chan change & sound | dry joints IC001, 002, RA2, 3 | 14-09-04 |
| Sony | BE-3B | lack of width - no EW | cct prot PS801 ICPF10 o/c | 14-09-04 |
| Sony | BE-3B KV25T1U | dead, no start up | R600 39k 5W in PSU (1-216-490-11) | 14-09-04 |
| Sony | BE-3B KVX2102U | dead, no start up | R600 39k 5W in PSU (1-216-490-11) | 14-09-04 |
| Sony | BE-3B KVX2182U | drop-out on one audio channel, may loose one channel completely | stereo decoder IC201 TDA2822M (875950221) | 14-09-04 |
| Sony | BE-3B KVX2582U | int crackling with stereo graphics switching between mute and stereo symbols | NICAM Xtal X1101 8.192MHz on A PCB | 14-09-04 |
| Sony | BE-3B KVX2582U | int operation from remote | SMD resitor pack RA2 near Micro is faulty (123341511) | 14-09-04 |
| Sony | BE-3B KVX2902U | E-W error | IC protector in the collector of E-W transistor | 14-09-04 |
| Sony | BE-3B KVX2902U | no E-W correction | CP801 N10 | 14-09-04 |
| Sony | BE-3B KVX2982U | blank raster/ distorted frame, R509,R510 burning | zener BZV85C15 on print side between pins 4 and 5 IC1852 s/c; R510, R509 0.47R 0.25W (124944311) | 14-09-04 |
|
|
| Sony | BE-3B KVX2982U | text mode reverts to TV mode after 10 min | it is Ok for older software versions | 14-09-04 |
| Sony | BE3B | All supply lines come up then go low ( StBy ) | Check pin 9 CN001 if high set in protection mode disconnect pin if set still fails to come on Replace IC002 Memory chip PtN | 14-09-04 |
| Sony | BE3B | Clicking noise during Nicam reception | TV02794R | 14-09-04 |
| Sony | BE3B | GOES TO STBY AFTER REPLACING IC605 7812 | REPLACE WITH ORIGINAL TYPE ICMCT7812CT Pt No. 8-759-279-76 | 14-09-04 |
| Sony | BE3B | LINE PULLING ON MACRO TAPES | REPLACE JUMPER WIRE JW802 , MOUNTED IN LOC L800 with ( 330R ) 3W res PtNo 121590821 | 14-09-04 |
| Sony | BE3B KV24WS1U | White horizonzal bars, crackling sound, led blinking sometimes 6-7 or 13 times, stuck in sby | Pin 15 (earth conn) on prescalar chip TSA 5511 or 5512 dry jointed | 14-09-04 |
| Sony | BE3B KV24WSIU | LED flashes 6 times at sw on - no action | could be memory problem (IC701) or dry joints tuner/multiway block connecting tuner pcb | 14-09-04 |
| Sony | BE3B KV25T1U | No pic, sound & EHT OK | R824 1k8 burnt & C815 dry joints | 14-09-04 |
| Sony | BE3B KV28FS0U | E/W dist & int width | Dry joints connector CN800 for int width - R835 27R 3w o/c for no E/W | 14-09-04 |
| Sony | BE3B KV28FX20U | Dead | TNY253P IC5605 P/N 875958419 osc/chopper IC, TLP721 IC5606 P/N 874901321 4 pin opto, 10uf 450V C5658, 0.47ohm fusible R5602 | 14-09-04 |
| Sony | BE3B KVX2182 | Tries to start with burst of EHT then reverts to st/by with LED perm lit | Insul washer on FOP chip (shorting -15v line to chassis) | 14-09-04 |
| Sony | BE3B KVX2582 | Reverts to st/by at sw on | C604/605/607 in psu | 14-09-04 |
| Sony | BE3B KVX2982U | Dead with components exploded in psu | IC600 STRS6708, IC601 TLP721, R601 1k burnt, Q601 2SC3852A s/c, D603 6.8V zener o/c, R644 100R o/c, IC602 SE135N s/c pins 2-3. | 14-09-04 |
| Sony | BE3B KVX2982U | No sound or pic - if A1 advanced OSD shows with e-w errors | The +12V supply down to +2V. IC605 12V regulator u/s. | 14-09-04 |
| Sony | BE3B KVX2982U | St/by only aft initial burst of EHT - disabling trip makes no difference | EEPROM IC002 & FOP chip TDA8179 (To disable prot dis D505) | 14-09-04 |