Make | Model | Problem | Solution | Date |
| | | |
Found: 37
|
Sony | BE4A KVM14M1U | At sw on, only 1 funct could be selected b4 lock up | Replace IC803 EEPROM 24C02 - used blank | 14-09-04 |
Sony | BE4A KVM14M1U | To enter service mode | Select OSD ,5,Vol+,TV TT appears in right hand corner. Select menu .Adjust with cursor keys .Standby to store new settings. | 14-09-04 |
|
Sony | BE-4 KV14T1U | coloured lines on top | EEPROM IC002 ST24C02CB1 (875937032) | 14-09-04 |
Sony | BE-4 KV14T1U | dead | LOPTr Q802 S2055N s/c, R615 0.46R (121737100) o/c, IC601 STRS5706 s/c | 14-09-04 |
Sony | BE-4 KV16WT1U | frame collapse | DJ L807 wire link to LOPTx earth | 14-09-04 |
Sony | BE-4 KV16WT1U | frame collapse (no picture) | R814 0.46R 0.5W (121781111) o/c, IC501 TDA9302, C504 100uF 50V, also replace D501 RGP10GP (871930243) or may fail again | 14-09-04 |
Sony | BE-4A KV21T3U | blank raster with flyback lines | A1 voltage too high, replace LOPTx | 14-09-04 |
Sony | BE-4A KV21T3U | no pic (blank video) | D722 (871999133) o/c on CRT | 14-09-04 |
Sony | BE-4A KV21T3U | volume goes to max, no remote or front control functions | Micro gets hot, replace Micro part no 875947506 | 14-09-04 |
Sony | BE-4A KVM2171U | frame collapse | R622 (HT feed) o/c, R814 0.47R safety (frame feed) o/c | 14-09-04 |
Sony | BE-4A KVM2171U | no text, excessive width, poor grey scale | NVM corruption. Replace IC002 new type ST24C02FB6 (875937032). Change C0255 from 47uF to 1000uF, add 5.6V zener from pin 8 IC002 (cathode) to earth, tighten earth spring around CRT in the shape of U | 14-09-04 |
Sony | BE4 | Dark pic | C823 0µ022 250v leaky in beam lim cct | 14-09-04 |
Sony | BE4 | Dead - LED blinks 6 times (Field fault) | TDA9302H FOP chip dry jointed and u/s | 14-09-04 |
Sony | BE4 | Dead - LED flashes 6 times then repeats | Over current problem - Loptx u/s | 14-09-04 |
Sony | BE4 | Field collapse | No 24v supply to IC501 - R814 0R47 ?w fusible o/c - improved type 1-249-443-11 introduced | 14-09-04 |
Sony | BE4 | No txt or OSD | R081 o/c, C810 also failed | 14-09-04 |
Sony | BE4 | Pic displaced down by 2cm | Volts on Q500 & 501 way out - Jungle chip MC44007P faulty | 14-09-04 |
Sony | BE4 | Reverts to st/by at sw on with 6 flashes from LED | over-current protection circuit (Q600, 602) is operating, usuallyprobs in LOP. To identify the cause, first dis FOP chip (IC501). If set switches on with frame collapse, replace IC501. If set fails to switch on, dis HT feed to LOPTx. This should give 4 flashes of st/by LED (no horizontal fly-back) showing that problem is in LOP. Check LOP comps before condemning LOPTx. If st/by LED continues to flash 6 times even with LOPTx disd, check R620 (270K) & R622 (470K) in over-current protection cct. | 14-09-04 |
Sony | BE4 | Txt can't be selected - nothing happens when you try | Enter service mode, and at the "TT" prompt type "18". This will turn teletext on or off depending on how it
was originally set. Sets which do not feature teletext or have the wrong version of IC001 fitted will only display P100 when teletext is selected. | 14-09-04 |
Sony | BE4 Chassis | Int trips off - led flashing 6 times | Blue screen momentarily at sw off - int s/c in crt | 14-09-04 |
Sony | BE4 KV14T1U | Auto grey scale lines visible at top of screen | EPROM ST24C02CB1 IC002 faulty | 14-09-04 |
Sony | BE4 KV14T1U | Dead - no led lit or flashing | 0.47R resistor from the 300volts input to the chopper TX
was O/C, replace STRS5706 chopper chip, still dead - LOPTr S2055N leaky If LOPTx is grey, R806 1.5R
with a 1.8R resistor Part number 1-216-352-11. | 14-09-04 |
|
Sony | BE4 KV14T1U | Dead | cracks in print around loptx | 14-09-04 |
Sony | BE4 KV21M3U | Field collapse | R814 0R47 in 24v supply o/c - use proper improved Sony type | 14-09-04 |
Sony | BE4 KV21T3U | Int dead | R607 0R56 2 watts had risen in value to nearly 2 ohms | 14-09-04 |
Sony | BE4 KVM2171U | Dead after half an hour | STRS5706 IC601 | 14-09-04 |
Sony | BE4/4A | Tripping with 6 flashes from LED & rush of EHT | LOPTx - EHT sect faulty | 14-09-04 |
Sony | BE4A | Dead - 6 blinks from led | Overvolts or current indicated - check HT (118v) - use dummy load; C608 10µ, C620 100µ 160v, STRS5706 poss & loptx | 14-09-04 |
Sony | BE4A | Dead - CP602 on sec psu o/c | Replacement cures fault only temp - CP602 to N75 (2.5A); Add 5v6 zener between pins 1 & 9 IC803, add 5v6 zener between pins 9 & chassis on print side of pcb | 14-09-04 |
Sony | BE4A | Dead - st/by LED flashes 4 times (No lop) | No line drive from IC301 MC44007P - chip u/s | 14-09-04 |