| Make | Model | Problem | Solution | Date |
| | | |
| Found: 16
|
| Sony | BE4A KVM14M1U | At sw on, only 1 funct could be selected b4 lock up | Replace IC803 EEPROM 24C02 - used blank | 14-09-04 |
| Sony | BE4A KVM14M1U | To enter service mode | Select OSD ,5,Vol+,TV TT appears in right hand corner. Select menu .Adjust with cursor keys .Standby to store new settings. | 14-09-04 |
|
|
| Sony | BE-4A KV21T3U | blank raster with flyback lines | A1 voltage too high, replace LOPTx | 14-09-04 |
| Sony | BE-4A KV21T3U | no pic (blank video) | D722 (871999133) o/c on CRT | 14-09-04 |
| Sony | BE-4A KV21T3U | volume goes to max, no remote or front control functions | Micro gets hot, replace Micro part no 875947506 | 14-09-04 |
| Sony | BE-4A KVM2171U | frame collapse | R622 (HT feed) o/c, R814 0.47R safety (frame feed) o/c | 14-09-04 |
| Sony | BE-4A KVM2171U | no text, excessive width, poor grey scale | NVM corruption. Replace IC002 new type ST24C02FB6 (875937032). Change C0255 from 47uF to 1000uF, add 5.6V zener from pin 8 IC002 (cathode) to earth, tighten earth spring around CRT in the shape of U | 14-09-04 |
| Sony | BE4A | Dead - 6 blinks from led | Overvolts or current indicated - check HT (118v) - use dummy load; C608 10µ, C620 100µ 160v, STRS5706 poss & loptx | 14-09-04 |
| Sony | BE4A | Dead - CP602 on sec psu o/c | Replacement cures fault only temp - CP602 to N75 (2.5A); Add 5v6 zener between pins 1 & 9 IC803, add 5v6 zener between pins 9 & chassis on print side of pcb | 14-09-04 |
| Sony | BE4A | Dead - st/by LED flashes 4 times (No lop) | No line drive from IC301 MC44007P - chip u/s | 14-09-04 |
| Sony | BE4A | Field collapse with visible line | STV9379 fop IC & 24v fusible next to loptx | 14-09-04 |
| Sony | BE4A Chassis | Frame collapse. Replaced frame output chip, but picture geometry was not OK. The voltage at pin 8 of MC44007P chip measured low. | If picture Geometry after replacing Vertical outp. Chip is not in order, replace also MC44007P. (Replaced also STR-S5706 in case an overvoltage caused the fault) | 14-09-04 |
| Sony | BE4A Chassis | Frame collapse. Replaced frame output chip, but picture geometry was not OK. The voltage at pin 8 of MC44007P chip measured low. | If picture Geometry after replacing Vertical outp. Chip is not in order, replace also MC44007P. (Replaced also STR-S5706 in case an overvoltage caused the fault) | 14-09-04 |
| Sony | BE4A KV25T1U | Corrugations and poor EHT stability | LOPTx | 14-09-04 |
| Sony | BE4A KVM2171U | Field collapse | R814 0R47 o/c | 14-09-04 |
| Sony | BE4A KVM2171U | Luma low, poor sync, field up at bottom & E/W bowing | OK when heated - C627 100uF 10V in the 5 volt rail, high ESR, Off pin 8 of IC603 | 14-09-04 |