| Make | Model | Problem | Solution | Date |
| | | |
| Found: 19
|
| Samsung | CB536Z P45S | Rolls aft 2 hrs | R210 240k | 14-09-04 |
| Samsung | CB5373 | Repeated blowing of SMR40200 | BU508AF on a hybrid panel can be used instead (leave pins 1 & 5 dis'd) & change HISO169B, 150v avalanche diode, 33µ cap | 14-09-04 |
|
|
| Sanyo | 25MT1 CB5956 EC3-A25 | Goes to st/by aft few secs | Pin 31 IC701 1v instead of 5v - R372 390k o/c | 14-09-04 |
| SANYO | CB5153 | DEAD | Q432 S/C CPC*SC2SD1651 | 14-09-04 |
| Sanyo | CB5156 | Dead - trips once with snatch of sound | LA7832 fop chip s/c, R364 4R7 2w hi res (24v feed); D351 dry joints | 14-09-04 |
| Sanyo | CB5156 | Thin dark vertical line on the left side of the picture | R433 DJ, located next to the SCART socket | 14-09-04 |
| Sanyo | CB5159 C21EF35NB | Dead | IV451 LA7832 FOP chip s/c, R364 4R7 ?w fusible o/c, C362 22µ 250v 180v smoother s/c, D351 dry joint | 14-09-04 |
| Sanyo | CB5159 C21EF35NB | No sound | Q2961/2962 2SC812L6 sm on nicam pcb both faulty- used BC846B in lieu, TDA7263 AF o/p chip u/s | 14-09-04 |
| Sanyo | CB5159 C21EF35NB | No Txt | No 5v (REF+) pin 6 IC1001 Txt dec chip SAA5281P/E- D1001 5v1 zener leaky | 14-09-04 |
| Sanyo | CB5949 EB2 | Int white flashes across screen removing vid signal | 27Mhz Xtal on Txt pcb | 14-09-04 |
| Sanyo | CB5957 Mk2 | Int low gain tuner | Dry joints tuner screening can | 14-09-04 |
| Sanyo | CB5959 | STUCK IN STANDBY | CHECK C422 FOR S/C | 14-09-04 |
| Sanyo | CB5959 EB2A25 | Int startup with motorboating from spkrs then no sound/vol OSD | TDA7263M audio o/p IC | 14-09-04 |
| Sanyo | EB2 CB5959 | stuck in stby | C442 s/c | 14-09-04 |
| Sanyo | EB2A CB5949 | Int trips at sw on - other times ok | Dry joint black jumper wire from chopper trfmr to IC351 vicinity | 14-09-04 |
| Sanyo | EC3 CB5153 | dead | Q432 2SD1651 s/c | 14-09-04 |
| Sanyo | EC3 CB5156 | drifts off tune | replace C105 1uF 50V near tuner | 14-09-04 |
| Sanyo | EC3 CB5156 | when switched on from stby, the set immediately reverts back to stby | in protection mode (pin 31 IC701 below 5V) due to R327 390k o/c | 14-09-04 |
| Sanyo | EC3A25 CB5956 | Dead with LED flashing dimly | HT at 57v, dry joint on black wire to side of chopper Trfmr | 14-09-04 |