Make | Model | Problem | Solution | Date |
| | | |
Found: 465
|
Astron | EC142 | Dead. | BU208A ( BU326A will do ) 22k in series with set-ht pot oc | 14-09-04 |
Beko | C14 | Clicks when chan change | C304 100nF | 14-09-04 |
|
Beko | C14 | Field collapse | R521 0R47 o/c - check also C517 22µ 63v for leak | 14-09-04 |
Beko | C14 | Sound - loud clicks from 1 chan with no sound | C348 or C350 100nF | 14-09-04 |
Beko | C14 | Sound - no surround decoding | C308 1.5pF | 14-09-04 |
Beko | C14 | Sound absent | IC301 TDA7263 & R341 5R6 2w fusible o/c | 14-09-04 |
Beko | C14 | Sound absent but returns when IC301 prodded | C235 100nF | 14-09-04 |
Beko | C14 | Sound chans unbalanced | C316 & C319 1nF | 14-09-04 |
Beko | C14 | Sound osc on 1 chan | C348 or C350 100nF | 14-09-04 |
Beko | C14 | Sound plays in Mono tho' Stereo displayed | C301 2n2 | 14-09-04 |
Beko | C14 | Sound varies on 1 chan - int | C310 &/or C312 10µ 63v | 14-09-04 |
Boots | C1417R | Flyback & Txt lines at top of pic | R307 10R 2w risen to 50R | 14-09-04 |
Daewoo | TVC14VP | Dead - led flashes red/green | R817 o/c | 14-09-04 |
Emerson | EWC1902 | An Emerson TV/VCR Combo unit. When you power on the TV
using the remote or manually at the TV, it comes on then shuts right
back off. | Can you hear any high voltage, when the TV starts?
if not, try to measure the secundairy voltages, and so check if there are shorted ciruits on the mainboard!
The primairy power supply will shut down when ever a short is detected on the secundary side (e.g. highvoltage or deflection circuit)
| 11-07-05 |
Etron | EC142 | Dead. | BU208A ( BU326A will do ) 22k in series with set-ht pot oc | 14-09-04 |
Etron | EC146 BG001-N | Flyback lines. | C312. | 14-09-04 |
Ferguson | ICC17 / 19 | Service mode access | Go to St/By, turn set off using power switch. When red LED goes off, hold down prog- and vol- keys on T.V and power up keeping both buttons held down for at least 8 seconds until STANDBY light goes yellow. To navigate through the menus use the arrow keys.To exit service mode put T.V into standby. | 14-09-04 |
Ferguson | ICC17 M6322 | Trips , LED flashes 7 times then goes to st/y | TL02 BF422 leaky | 14-09-04 |
Ferguson | ICC17 M8422U | Dead with mains fuse blown | DP06 BZW04-342 across mains rect cap (not shown on all cct diags) | 14-09-04 |
Ferguson | ICC17 W7023U | Dead | LOPTx faulty - had brown gunge on the top - replacement comes with 2coils, 2 caps & 4 sm res | 14-09-04 |
Ferguson | ICC17 W7023U | Trips at sw on with led flashing 3 then 2 then 7 then 2 flashes then reverts to perm illum | LOPTx faulty- check for brown gunge on top - also obtain mod kit (psu will not run unloaded) | 14-09-04 |
Ferguson | ICC19 Thomson 32WS83KP | starts up then trips and shuts down | IB01 TEA5101B on CRT | 14-09-04 |
|
Ferguson | IKC1 | Scan coils overheat tho pic ok | Scan coils faulty | 14-09-04 |
Ferguson | M8421U ICC17 | Dark bands running up screen with corrugation/pulling in the bands | Fit Line output transformer kit (35096370)
Notes: The LOPT kit consists of a new transformer (10608640) to replace the original (10516050) for this 33" medium planartube (MP), plus a 100k 0.1w surface-mounted resistor to replace RL48 (76k8). | 14-09-04 |
Ferguson | W7023U ICC17 | Dead with led flashing twice, pausing then flashing 7 times | LOPTx Part No. 35123670 | 14-09-04 |
Fidelity | C14M06 | Int field collapse | D25 1N4002 pin 6 IC10 TDA3653 int o/c | 14-09-04 |
Fidelity | LC169 | No sound/sync | R109E - part of chain of 10 x 5k6 res o/c | 14-09-04 |
GEC | C1041H | Grainy picture & noisy sound. | R334 ( 10k ) | 14-09-04 |
GEC | C1402H CVC801 | Startup - dead. | IC700 ( 7812 ) 12v reg , T873 , IC870 ( TDA2140 ) check by change | 14-09-04 |
GEC | C1407H | Dead - with whinning noise. | 2D910 ( 3V zener ) s/c. | 14-09-04 |