Make | Model | Problem | Solution | Date |
| | | |
Found: 230
|
Ferguson | C3615U Combi | Switches off aft 10 secs with tape jammed | RW002 1R 1w safety res on deck pcb - also check fuse link FW003 (behind on/off sw near white ribbon conn) | 14-09-04 |
Ferguson | C3615UT | Hotel mode removal | Press simultaneously on the PR-, STOP and AC on/off button on the front of the combi. Adjust using arrow keys on the remote, press ok. | 14-09-04 |
|
Ferguson | C3615UT | Hotel mode reset | Press PR-, STOP & AC on/off button on front of combi. Adj using arrow keys on R/C, press ok. | 14-09-04 |
Ferguson | C3615UT | No R/C response | 3 legged IR Rx faulty | 14-09-04 |
Ferguson | C3615UT | Txt int lost | QX51 27Mhz Xtal on Txt pcb replaced | 14-09-04 |
Ferguson | TX90E C39F | Field cramp & roll at sw on | IL01 TDA8214B | 14-09-04 |
Goldstar | CF25C36 NC51B | Wont stop when in search - existing chans may be slightly off tune | IC182 5v reg producing low o/p | 14-09-04 |
Goldstar | CI21A80FA PC31A | Goes in/out of st/by - otherwise dead | No volts to HT rect D804 - L804 dry joints | 14-09-04 |
Goldstar | PC-33 | Vert dist with lines across screen | C305 6µ8 100v bi-polar | 14-09-04 |
Goldstar | PC31A | dark lines, whine | C812 0.22µ, 63v connected to pin 7 of IC801 | 14-09-04 |
Goldstar | PC31A | Dead - psu running | Line dr was 20khz, No 12v to IC501 TDA8362 - Reg IC401 7812 o/c | 14-09-04 |
Goldstar | PC31A | Momentarily trips on bright scenes | R802 680k had wrong value (68k) fitted | 14-09-04 |
Goldstar | PC31A | Poor HT reg & sw off on prolonged bright pic | R802 had incorrect value of 68k instead of 680k | 14-09-04 |
Goldstar | PC33J | field collapse | fit KITPC33J from CPC - includes diodes chip etc | 14-09-04 |
Goldstar | PC33J | Field o/p chip repeatedly fails | Fit mod kit KITPC33J | 14-09-04 |
Goldstar | PC33J | Lack of height | FR301 1R in fop hi res | 14-09-04 |
Grundig | CUC3300 | POOR FOCUS OR PICTURE SO DIM IT CAN HARDLY BE SEEN | C433 1000uF 25v ( NOT 16v AS ORIGINALLY FITTED ) DO NOT RUN SET IN THIS CONDITION AS THE SCAN COILS MAY OVERHEAT AND CRACK CR | 14-09-04 |
Grundig | CUC3300 | Poor purity & focus. | C433 ( 1 , 000uf , 25v ) | 14-09-04 |
Grundig | CUC3300 CUC3400 | Poor focus | Usually the focus pot on tripler faulty but check C433 1000µ for s/c, if its 16v working - fit 25vw (can cause scan coils to overheat) | 14-09-04 |
Grundig | CUC3400 | +B decreasing when average brightness of picture increases. | Change C611 47uF cap. | 14-09-04 |
Grundig | CUC3400 | Arcing/random chan change | tripler | 14-09-04 |
Grundig | CUC3400 | Blue raster with fb lines | TDA3505 vid proc chip IC9531 on chroma board | 14-09-04 |
|
Grundig | CUC3400 | dead | on/off sw u/s CHS - G102 | 14-09-04 |
Grundig | CUC3400 | Dead - & tripping. | Set HT control ( R637 ) int o/c , D666/D664 s/c , IC686 78M05 | 14-09-04 |
Grundig | CUC3400 | Dead - all fuses intact | D691 BYV28/100 s/c (20v supply) | 14-09-04 |
Grundig | CUC3400 | Dead - repeatedly blows T661 | Replace IC655 TDA3640, D666 RGP30M, R637 1k preset, C661 47µ 63v, D662 ZPD3v9, R661 1R & C667 0µ15 or 2µ2 | 14-09-04 |
Grundig | CUC3400 | DEAD 800mA FUSE BLOWN | DRY JOINTS ON CHOPPER TX CHECK D663 664 666 C653 4n7 C667 2u2 | 14-09-04 |
Grundig | CUC3400 | Dead or tripping | Set HT pot R637, D666 BYV16 s/c, D664 BA159 s/c or IC686 78M05 s/c | 14-09-04 |
Grundig | CUC3400 | Dead with buzz from Ipsalo Tfmr | The +M supply ok at 11v in st/by but dropped instead of increasing to 20v when sw on. C630 0µ68 leaky | 14-09-04 |
Grundig | CUC3400 | Dead, 800mA SI642 fuse o/c, chopper T661 BUT11A s/c | Check for dry joints Ipsalo tfmr or D663, 664 & 666 faulty also check C667 2µ2 | 14-09-04 |