| Make | Model | Problem | Solution | Date |
| | | |
| Found: 12
|
| Mitsubishi | CT21M5 EE4 | Dead - blowing SOC2000 cct prot | Microprocessor s/c +5v pin to chassis | 14-09-04 |
| Mitsubishi | CT21M5 EE4 | No Txt or auto tune/store | eset options in eeprom from service mode | 14-09-04 |
|
|
| Mitsubishi | CT21M5BT EE4 | Int loss of pic - sound still present | Invisible dry joint IC650 TEA5101B RGB o/p chip on crt base | 14-09-04 |
| Mitsubishi | CT25M5BT EE4 | Field collapse | TEA2031A (IC551) & supply decoupler R516 0R82 safety resistor. | 14-09-04 |
| Mitsubishi | CT25M5BT EE4 | Green LED only - prev int off - HT present | No line dr from IC201, no micro activity, replace EEPROM 24C08 & set up | 14-09-04 |
| Mitsubishi | EE4 | Dead or int dead - brief flash of green led at sw on | Dry joints opto isol PC951 | 14-09-04 |
| Mitsubishi | EE4 | Service mode accessing | press the service switch (s701, next to the aerial socket) and then button 9 within 5 seconds Press the * button to toggle between the VCJ or OPTION adjustment display.
Press buttons 2 or 8 to increase or decrease the adjustment code number. Press buttons 6 or 4 to increase or decrease data value. After the adjustments, press 0 to write the adjustment data to the EEPROM.To cancel a change, press button 1 and all data adjusted since the last EEPROM write will be reset.TUN 0
Option settings for CT25AV1BS = SAT 1, AUD 10, ATS 1, STD 1, SYS 1, AV1 2, EEX -, SPK 1, EEP -, ABG 02, A1 02, AL 00, ADK 15, MNP 70, TXT -, FFT 1, VOL 74, HYP 1, SCP 20, FMP 23 | 14-09-04 |
| Mitsubishi | EE4 | Trips once at sw on - ok on dummy load | TEA5101B RGB o/p chip IC660 s/c | 14-09-04 |
| Mitsubishi | EE4 (M5 models) | To enter service mode | Press & release S701 next to aerial socket, then press "9" on hset within 5 secs. Buttons 2 & 8 select adj code, buttons 4 & 6 adj data value. Button 1 cancels written data, button 0 stores data into EEPROM see article TV Jan 99 for more details | 14-09-04 |
| Mitsubishi | EE4 CT21M5BT | Reverts to st/by aft 15mins with a sqeal | HT was too high at 137V, due to R954 (120K in this set) going high | 14-09-04 |
| Mitsubishi | EE4 CT25M5BT | Chopper Tr blows aft few days | Replace Q901 (chopper), R901 (4R7 10W), D909 (3V Zener) and change 220R resistor on the print side of the CRT PCB to 1K2 1/2 watt. | 14-09-04 |
| Mitsubishi | EE4 CT25M5BT | Dead - blows chopper tr s/c | mod, i.e. change the 220R res on print side of CRT base to 1K2 1/2watt,this apparantly prevents a surge from blowing the chopper at switch off | 14-09-04 |