| Make | Model | Problem | Solution | Date |
| | | |
| Found: 45
|
| Philips | FL1.0S | 50Hz buzz noticable through speaker | Check/replace IC7680 on the SSP - TDA8425, pseudo stereo IC.
(4822 209 63734).
| 14-09-04 |
| Philips | FL1.0S | Bad focus or focus varies in a new set or after CRT replacement | Possible solution:
Short circuit the focus and the G2 pins of the picture tube with the
aquadag coating. Switch the set on for approximately 5 seconds.
After this return the set to its original condition. Check if the
focus adjusted normally. If not repla | 14-09-04 |
|
|
| Philips | FL1.0S | Bad or no functioning of the TDA4680/V4. | Check/replace IC7430 TDA4680/V4 (4822 209 31592).
It is recommended to add a zener diode BZX79-C12 (4822 130 34197)
between pin 28 of the TDA4680/V4 and anode to ground.
REMARKS :
Introduced in production in week 9140.
| 14-09-04 |
| Philips | FL1.0S | BUX85F in mikroSOPS defective | Change the value of C2260 to 4n7F, replace 7270 with transistor
BD825 (4822 130 41746).
| 14-09-04 |
| Philips | FL1.0S | Channel 21 and 28 frequency range cannot be tuned in. | Use software version V2.4 or higher; IC7115 on the SSP
(4822 900 10298).
REMARKS :
Introduced in production in week 9218.
| 14-09-04 |
| Philips | FL1.0S | Colored picture or picture is green/red, fly-back lines | Check zenerdiode 6450 on pin 19-IC7430 on the LSP. New diode must
be Philips (Telefunken does not work), 4822 130 81512
| 14-09-04 |
| Philips | FL1.0S | Correction to service information FL 95.01 | Correction to service information FL 95.01
------------------------------------------
Correction in the overview of 100Hz and Proscan boxen.
The replacement for service code 4822 212 30534 must be 4822 212 31231
The replacement for service code 4822 21 | 14-09-04 |
| Philips | FL1.0S | Crackling/toggling sound or intermittent Nicam sound. | This complaint is due to poor reception or reflection problem and
is very much depending on the customers location.
Service solution:
- Change item 1045 on the Multi Sound Bi Nicam Panel into adjusting
coil 5,85 MHz (4822 156 11157)
- Change item 1045 | 14-09-04 |
| Philips | FL1.0S | Does not start. | Check/replace C2241 330 uF (4822 124 42208) on LSP.
If C2241 is defective it is recommended to change the value of
C2228 on the LSP into 33nF (4822 122 31981).
REMARKS :
Introduced in production in week 9325.
| 14-09-04 |
| Philips | FL1.0S | Does not start. | Check D6228 on the LSP.
If D6628 is defective it should be replaced by S0824NH-1DA
(4822 130 20277). It is recommended, for PWB version lower than .3,
to add a capacitor of 47nF (4822 121 43526) across the cathode and
gate of D6228. It is recommended, fo | 14-09-04 |
| Philips | FL1.0S | During production an EEPROM protection panel (4822 | During production an EEPROM protection panel (4822 212 31266) is
introduced. Together with this also the following components have
to be changed:
On the Small signal panel:
- Add position 3256 and 3257 4k7 (4822 051 10472)
- Delete position 3280 and 3281
| 14-09-04 |
| Philips | FL1.0S | Instant colour/tint change problem. | Use latest software version;
FL1.0S V1.9 (4822 900 10297)
FL1.0S LAT/NTSC V2.4 (4822 900 10298)
REMARKS :
Introduced in production in week 9218.
| 14-09-04 |
| Philips | FL1.0S | Intermittent NICAM decoding. | Replace C2108 on the multi sound panel into 33pF
(4822 126 10324).
REMARKS :
Introduced in production week 9129
| 14-09-04 |
| Philips | FL1.0S | Intermittent NICAM decoding. | Replace C2108 on the multi sound panel into 33pF
(4822 126 10324).
REMARKS :
Introduced in production week 9129
| 14-09-04 |
| Philips | FL1.0S | Jitter | In PIP unit change the value of R3336 to 4k7.
| 14-09-04 |
| Philips | FL1.0S | LEDs blinking; error code 99. | Check TS7504 on the LSP (BU508AF; 4822 130 61265). If TS7504 needs
to be replaced it is recommended to change R3418 on the LSP into
200 ohm (4822 051 10201).
REMARKS :
Introduced in production in week 9202.
| 14-09-04 |
| Philips | FL1.0S | Low Brightness TXT and OSD, Picture OK | If this condition occurs, check the Option Codes.
Resetting the Option Code numbers as per the Service Manual provided the cure. | 14-09-04 |
| Philips | FL1.0S | Low frequency hum from subwoofer, buzz from right hand squeeter. | Check DC level on pin 1 and 9 of IC7011 (TDA1521).
If not correct, replace (4822 209 63913). | 14-09-04 |
| Philips | FL1.0S | Modification improved bandpass for high frequency | Modification improved bandpass for high frequency in -/61 sets
--------------------------------------------------------------
On the Korean stereo panel the following items are changed:
- item C2080 added 10nF 50V (4822 121 41857)
- item C2083 changed int | 14-09-04 |
| Philips | FL1.0S | Modification TDA4680/V4 -> TDA4681/V1 on the SSP | Modification TDA4680/V4 -> TDA4681/V1 on the SSP
------------------------------------------------
During production IC7430 TDA4680/V4 has been changed into the
TDA4681/V1 (4822 209 32271). Together with the IC also some other
components must change:
- ite | 14-09-04 |
| Philips | FL1.0S | No colors in TV mode | Check IC7365 (TDA4650) on the SSP (4822 209 30837)
| 14-09-04 |
| Philips | FL1.0S | No sound, "ON, Standby, I" LEDs blinking | 10MHz crystal 1602 on the SSP defective, 4822 242 80276
| 14-09-04 |
|
|
| Philips | FL1.0S | Noise PIP picture | Change the following items on the PIP module 4822 212 30303:
- item C2020 added 10 uF 50V (4822 124 40435) soldered with + to
item 9031 and with - to item 9024
- item R3403 changed into 150 ohm (4822 051 10151)
- item R3410 changed into 130 ohm (4822 0 | 14-09-04 |
| Philips | FL1.0S | Overview of SOPS repair kits | Overview of SOPS repair kits
----------------------------
FL1.0 AG00 upto AG03 4822 310 20492
FL1.0 AG04 and higher 4822 310 31921
FL1.0S 4822 310 31924
FL1.1 25" and 28" 4822 310 31919
FL1.1 33" 4822 310 31932
FL1.1S | 14-09-04 |
| Philips | FL1.0S | Picture disappears (fly back lines), ON STEREO and DUAL LEDs blink | Check IC7430 (TDA4680). When TDA4680 is too hot there is no picture
(4822 209 31592).
| 14-09-04 |
| Philips | FL1.0S | Picture disappears shortly after 30" or control does not function. | When hot, 13,5 MHz clock stops working; change the value of R3123
to 1k2.
| 14-09-04 |
| Philips | FL1.0S | Picture often dark | Check IC7201 in High End-box (SAA9042P/A; 4822 209 31851)
| 14-09-04 |
| Philips | FL1.0S | Picture twists from top | Voltage of pin 8-IC7450 (TDA3654Q) on the LSP has raised to ca. 20 V.
Check diode 6451 (BZX79/C3V6; 5322 130 34834 or BZX79/C10; 4822 130 61219) | 14-09-04 |
| Philips | FL1.0S | Picture twists from top | Voltage of pin 8-IC7450 (TDA3654Q) on the LSP has raised to ca.
20 V. Check diode 6451 (BZX79/C5V6; 4822 130 80954).
| 14-09-04 |
| Philips | FL1.0S | Picture twists from top | Voltage of pin 8-IC7450 (TDA3654Q) on the LSP has raised to ca. 20 V.
Check diode 6451 (BZX79/C3V6; 5322 130 34834 or
BZX79/C10; 4822 130 61219)
| 14-09-04 |