Make | Model | Problem | Solution | Date |
| | | |
Found: 49
|
Philips | FL4.17 | "NVM write protection enabled" message on screen. | Startup problem or 'NVM write protection enabled' message on screen
after replacement of NVM
(ST24C08CB1; 4822 209 32283) with a ST24C08CB6 (4822 209 33113).
Use as replacement the ST24C08 1 (9311 021 36682). | 14-09-04 |
Philips | FL4.17 | After 10 minutes picture becomes red from right side | C2395 on the LSP poorly soldered.
| 14-09-04 |
|
Philips | FL4.17 | Antenna input: no sound. External input: sound O.K. | Check whether crystal 1602 (stereo decoder) 10MHz oscillates.
If not replace X1602 (4822 242 80276).
| 14-09-04 |
Philips | FL4.17 | Bad focus or focus varies in a new set or after CRT replacement | Possible solution:
Short circuit the focus and the G2 pins of the picture tube with the
aquadag coating. Switch the set on for approximately 5 seconds.
After this return the set to its original condition. Check if the
focus adjusted normally. If not repla | 14-09-04 |
Philips | FL4.17 | Bad pict. No menu. Dark bars over pict. Red pict. in dig.scan mode. | +5V was 4,3V instead of 5,1V.
IC7551 (LM358N 4822 209 70672) defective.
IC7209 (SAA7158 4822 209 31059) Bendic defective.
| 14-09-04 |
Philips | FL4.17 | Bad picture. Picture scrolls. No RC reaction. | +5V was 4,1V instead of 5,1V. Replace IC7551 (LM358N; 4822 209 70672)
| 14-09-04 |
Philips | FL4.17 | Bad synchronization with external signals | Delete position 3115 on the ECO 100Hz box.
REMARKS :
Introduced in production in week 9415.
| 14-09-04 |
Philips | FL4.17 | Blank picture. OSD not synchronised and too large, no TXT. | Check/replace memory IC 7900 (ST24C08CB1; 4822 209 32283).
| 14-09-04 |
Philips | FL4.17 | Both languages can be heard by Dual Nicam signals | For FL1-PTV change the software into V89; 4822 900 10732
For all other FL sets change the software into V88; 4822 900 10723
REMARKS :Introduced in production from week 9614 onwards. | 14-09-04 |
Philips | FL4.17 | BUX85F in mikroSOPS defective | Change the value of C2260 to 4n7F, replace 7270 with transistor
BD825 (4822 130 41746).
| 14-09-04 |
Philips | FL4.17 | Colored picture or picture is green/red, fly-back lines | Check zenerdiode 6450 on pin 19-IC7430 on the LSP. New diode must
be Philips (Telefunken does not work), 4822 130 81512
| 14-09-04 |
Philips | FL4.17 | Colour loss at photofinish and scan. | Change position 6003 on the ECO-box into a LL4148 (4822 130 80446).
REMARKS :
Introduced in production in week 9424. | 14-09-04 |
Philips | FL4.17 | Correction to service information FL 95.01 | Correction to service information FL 95.01
------------------------------------------
Correction in the overview of 100Hz and Proscan boxen.
The replacement for service code 4822 212 30534 must be 4822 212 31231
The replacement for service code 4822 21 | 14-09-04 |
Philips | FL4.17 | Correction to service information FL 95.01 | Correction to service information FL 95.01
------------------------------------------
Correction in the overview of 100Hz and Proscan boxen.
The replacement for service code 4822 212 30534 must be 4822 212 31231
The replacement for service code 4822 21 | 14-09-04 |
Philips | FL4.17 | Correction to service manual FLx.14/16/17 | Correction to service manual FLx.14/16/17 and FLx.24/26/27.
-----------------------------------------------------------
The code number of position 1200 (fuse 3,15 A) is wrong.
The correct code number is 4822 070 33152. This fuse is situated on
the LSP i | 14-09-04 |
Philips | FL4.17 | Correction to the Service Manual | Correction to the Service Manual
--------------------------------
In circuit diagram B on page 7 of the service manual
FL1.14/FL2.14/FL1.16/FL2.16 and FL 1.17 the resistors 3624 and 3625
are not drawn.
These resistors should be drawn on the position of 96 | 14-09-04 |
Philips | FL4.17 | Crazy behaviour: No response from RC or controls. | Other phenomenas: volume up/down, spontanuous service mode etc.
etc. in areas with TOP-teletext.
Replace control software by replacing EPROM IC7002 to version V83
(4822 900 10506). For easy mounting also the controlboard 7115
(on SSP) can be replaced by | 14-09-04 |
Philips | FL4.17 | Dark picture, only green led, no menu or OSD. | +5V supply was 4,1V. Voltage D6551 was 4,3V instead of 5,6V.
Check/replace D6551 (4822 130 80954).
| 14-09-04 |
Philips | FL4.17 | Four dark bars over the picture. | The +5 volt was 5.6 volt instead of 5.1 volt.
Check/replace IC7551 (4822 209 70672).
| 14-09-04 |
Philips | FL4.17 | How to enable/disable "Child Lock" | Press "MENU" button on Remote Control. When the menu appears on the
screen, you select "SPECIAL FEATURES" (this expression is language
dependent)
Within "SPECIAL FEATURES", the "CHILD LOCK" can be enabled or
disabled.
| 14-09-04 |
Philips | FL4.17 | Jitter | In PIP unit change the value of R3336 to 4k7.
| 14-09-04 |
Philips | FL4.17 | Low Brightness TXT and OSD, Picture OK | If this condition occurs, check the Option Codes.
Resetting the Option Code numbers as per the Service Manual provided
the cure.
| 14-09-04 |
|
Philips | FL4.17 | Low frequency hum from subwoofer, buzz from right hand squeeter. | Check DC level on pin 1 and 9 of IC7011 (TDA1521).
If not correct, replace (4822 209 63913).
| 14-09-04 |
Philips | FL4.17 | No colors in TV mode | Check IC7365 (TDA4650) on the SSP (4822 209 30837)
| 14-09-04 |
Philips | FL4.17 | No sound, "ON, Standby, I" LEDs blinking | 10MHz crystal 1602 on the SSP defective, 4822 242 80276
| 14-09-04 |
Philips | FL4.17 | Noise on high volume | Perform the following modifications on the SSP:
Add on position 3618 4,7nF (4822 122 31784)
Add on position 3619 jumper (4822 051 10008)
Connected in series from 2604/4610 to earth.
Change position 4610 into 1k ohm (4822 051 10102) | 14-09-04 |
Philips | FL4.17 | Overview of doors for FL4 styling | Overview of doors for FL4 styling
---------------------------------
4822 432 93229 Door for 29" FL4.17/FL4.27
4822 432 93393 Door for 29" 4GFL2.20E AA
4822 432 93312 Door for 29" FL4.16/FL4.26
4822 432 93382 Door for 29" GFL2.20E AB
4822 432 93271 Do | 14-09-04 |
Philips | FL4.17 | Overview of SOPS repair kits | Overview of SOPS repair kits
----------------------------
FL1.0 AG00 upto AG03 4822 310 20492
FL1.0 AG04 and higher 4822 310 31921
FL1.0S 4822 310 31924
FL1.1 25" and 28" 4822 310 31919
FL1.1 33" 4822 310 31932
FL1.1S | 14-09-04 |
Philips | FL4.17 | Picture disappears (fly back lines), ON STEREO and DUAL LEDs blink | Check IC7430 (TDA4680). When TDA4680 is too hot there is no picture
(4822 209 31592).
| 14-09-04 |
Philips | FL4.17 | Picture disappears shortly after 30" or control does not function. | When hot, 13,5 MHz clock stops working; change the value of R3123
to 1k2.
| 14-09-04 |