| Make | Model | Problem | Solution | Date |
| | | |
| Found: 1025
|
| Amstrad | CTV2020/2028 Bush 2866 | Searches but finds no sigs | R124 15K 2W O/C located
behind the PSU in the centre nearest the front controls | 14-09-04 |
| B & O | Hybrid | Teletext - interference. | 4 Page lay out. | 14-09-04 |
| Beko | 2841ND - 14.1 chassis | Lines across top 3 - 4 inches of pic | R422 35v feed to IC501 fop chip never been soldered | 14-09-04 |
| Bush | 2850NTX Schneider TV4 | Bent verticals and pulsating width (Scene Dependent) | Replace CC808 4N7 SMD primary side of PSU you will probably find that
the pcb in this area has taken some heat. | 14-09-04 |
| Co-Op | 63 Bush | Dead. | 4D14. | 14-09-04 |
| Daewoo | GB14H1N | No tuning - supply & clk/data lines ok | Tuner faulty - replaced Type DT5-BF18D pt no 48597-19930 | 14-09-04 |
| Daewoo | GB14H1N | Service mode entering | Press "Norm-av-sleep-clear-stby" on R/C | 14-09-04 |
| Daewoo | GB14H1N | Sound absent & snowy pic aft re-assemby | Check pl/skt conns of spk - can be accidentally put in set AGC skt | 14-09-04 |
| Daewoo | GB14H1N | Won't come out of st/by, sw off when playing, OSG corrugated - all int | I826 3.3v reg LE33CZ on front of pcb - available From Farnell | 14-09-04 |
| Daewoo | GB14H1T | Service mode entering | On hset press Blue > Yellow > Green > Red > Stby sequencially. When brought out of st/by should be in service mode. Use buttons 1 & 4 for Slope Adjust; 2 & 5 for Vert Centre; Use buttons 3 & 6 for Vert Amp... | 14-09-04 |
|
|
| Daewoo | GB14H1T | Sync absent | eeprom - [clock & data lines on video ic were low by approx 1v] | 14-09-04 |
| De Graff | D59HZ5 | Dead - both green leds flashing | Low serial data line at micro. When serial data pin of MC44130P sound proc chip dis'd set came on without sound - sound chip proc u/s | 14-09-04 |
| Ferguson | ICC19 Thomson 32WS83KP | starts up then trips and shuts down | IB01 TEA5101B on CRT | 14-09-04 |
| Ferguson | M7073GH | Bright white pic with poor focus | Altering focus control affects amplitude of video at crt cathodes - CRT faulty | 14-09-04 |
| Ferguson | TX100 (Turkish) | Switches to Stby after a while. | Change two 5V regulators in the control board.(TDD1605) | 14-09-04 |
| Ferguson | TX100 Chassis (Turkish) | Switches to Stby after a while. | Change two 5V regulators in the control board.(TDD1605) | 14-09-04 |
| Ferguson | TX807 Thomson 14MS15UT | dead, no LED | DP25 RGP10 s/c | 14-09-04 |
| Ferguson | TX91 Thomson 10MH73B 10MG73B | dead | SMD TF21 near LOPTx not soldered in factory | 14-09-04 |
| Ferguson | TX91 Thomson 10MH73B 10MG73B | dead on 12V supply (car supply) | RD09, RD19 22R 0.5W fusible | 14-09-04 |
| Ferguson | TX92 M7073GH | Changes chans on its own | Dry joints IR01 micro | 14-09-04 |
| Finlandia | C/D66KZ6/F Eurostereo CHA2 | stuck in st/by, if you try to switch it on, chan 1 appears in display for 5 secs then reverts back to st/by with green led flashing on front. | line driver transistor faulty | 14-09-04 |
| Finlandia | C51HZ6 | Tuning store/lock code - press within 5 sec | A/Red,0/AV,Step,Store | 14-09-04 |
| Finlandia | C59HZ6 | Dead - LOPTr S2000AF leaky | When replaced arcing sound from LOPTx, but was due to caps C623/4 & C523 (all 220uf), C622 (470uf 25v) & check for dry joints | 14-09-04 |
| Finlandia | C59HZ6 | Line stage inop | Field chip ICB570 (TDA8170) faulty (checked ok) | 14-09-04 |
| Finlandia | C59HZ6 | Tuning store/lock code - press within 5 sec | A/Red,0/AV,Step,Store | 14-09-04 |
| Finlandia | C66HZ6 | Tuning store/lock code - press within 5 sec | A/Red,0/AV,Step,Store | 14-09-04 |
| GEC | 2002H | Raster - bright screen & flyback lines. | R258 o/c. | 14-09-04 |
| GEC | C1041H | Grainy picture & noisy sound. | R334 ( 10k ) | 14-09-04 |
| GEC | C1402H CVC801 | Startup - dead. | IC700 ( 7812 ) 12v reg , T873 , IC870 ( TDA2140 ) check by change | 14-09-04 |
| GEC | C1407H | Dead - with whinning noise. | 2D910 ( 3V zener ) s/c. | 14-09-04 |