Make | Model | Problem | Solution | Date |
| | | |
Found: 22
|
Akai | Various | To enter service mode | Press Mute, OK, TV in sequence | 14-09-04 |
B & O | Beovision 8802 Type 7001 | Blank raster, no sound, OSD OK | R1 1,5Ohm o/c, TR1-TR2 BC 338-25 o/c, D1 13V Zener s/c
| 14-09-04 |
|
B & O | Various | Dead - Tr1 in PSU s/c | Check C12 for dry joint in snubber of psu | 14-09-04 |
Beko | Various | Field collapse | Check R717 & R722 for o/c | 14-09-04 |
Beko | Various | Field top foldover | 220R res over scan coils o/c | 14-09-04 |
BPL | Various | Field top foldover | 220R res over scan coils o/c | 14-09-04 |
Bush | 28ZKF Orion 4400 | Dead with faulty on/off sw | Dry joints also LOPTr S2000AF s/c & LOPTx from SEME LOPTX1277 at ?18.95 Part S065621409 | 14-09-04 |
Bush | WST Professional 4400 series | Service Mode access | hold menu button while turning CTV on until the red LED lights up. Release the menu button and press standby. | 14-09-04 |
JMB | 134TX Orion | AGC type overload | Main micro under can not seated properly | 14-09-04 |
JMBC | 1499BA (Orion) | St/by only | New EEPROM ordered from CPC cured problem | 14-09-04 |
LG | Various | Modifying R/C to access service modes | There is a service remote availiable but if you have a
remote which uses an SAA3010T IC , simply connect a tact switch between pins 1 & 11 to access the service mode . | 14-09-04 |
Mitsubishi | Various | Int RGB variations/fback lines | Dry joints crt base | 14-09-04 |
Onwa | various | Int dead / fizzing | Check HT relay | 14-09-04 |
Onwa | Various | The Onwa TV PSU | See TV Mag Feb 1998 | 14-09-04 |
Philips | Various | Accessing service mode | try pressing the following keys on the user remote control- 0,6,2,5,9,6,OSD | 14-09-04 |
Realistic | Portavision 16-7070 | No picture | C74 4µ7 25v bipolar cap leaky | 14-09-04 |
Samsung | Various | Entering Service Modes | Press standby, display, menu, mute, standby
Press standby, picture standard, help, sleep, standby | 14-09-04 |
Samsung | Various | Entering Service Modes | Press standby, display, menu, mute, standby | 14-09-04 |
Siemens/Blaupunkt | Chassis100/21 (Control section with hybrid Siemens Ics) | Set can not be switched to Stby with the remote control. All other functions O.K | Switch the TV to Stby from the on/Stby switch on the front panel.Hold down the"ME" button and switch the TV on.Press CS. It should work normally now. | 14-09-04 |
Siemens/Blaupunkt | Chassis100/21 (Control section with hybrid Siemens Ics) | To set normal values for Bright/Contr/Col/Volume | Switch set to Stby. Hold down "ME"button, until set switches on. Adjust bright,contr etc and press "ME" again to memorise. | 14-09-04 |
Siemens/Blupunkt | Chassis100/21 (Control section with hybrid Siemens Ics) | Set can not be switched to Stby with the remote control. All other functions O.K | Switch the TV to Stby from the on/Stby switch on the front panel.Hold down the"ME" button and switch the TV on.Press CS. It should work normally now. | 14-09-04 |
Siemens/Blupunkt | Chassis100/21 (Control section with hybrid Siemens Ics) | To set normal values for Bright/Contr/Col/Volume | Switch set to Stby. Hold down "ME"button, until set switches on. Adjust bright,contr etc and press "ME" again to memorise. | 14-09-04 |