Make | Model | Problem | Solution | Date |
| | | |
Found: 113
|
Bush | 1497ITV/3 11AK20S | Height stretched & width in on rh side | HT pot never been soldered | 14-09-04 |
Bush | ITV2100 | Sound int goes with crackle aft 1/2 hr | Although freezing O/P IC TDA7263 temporary cure - 18Mhz Xtal was faulty | 14-09-04 |
|
Bush | ITV2101 | R/C not working | Needs initiallising - Hold left, down, right & 1 buttons together | 14-09-04 |
Bush | ITV8401 11AK20S | St/by only - r/c not operating tv | Initialise remote by pressing arrow L, arrow R & arrow Down as well as "1" at the same time | 14-09-04 |
GEC | C2290H 2036 Hit | Dull raster may not have any colour. | IC ( TDA3561A ) decoder. | 14-09-04 |
Goldstar | CIT 2172X | int start up, int no pic, int txt | C811 47µ 25v, C812 100µ 16v,C808 1µ 50v, C813 100µ 16v remove glue, check relay | 14-09-04 |
Goldstar | CIT 2190F | No sound. | CHECK FOR MUTE STATE IC1401 | 14-09-04 |
Goldstar | CIT2068F | St/by only - if mains sw held in snowy raster shows | Micro IC701 pins 31 & 32 had no 10Mhz signal present - Xtal faulty | 14-09-04 |
Goldstar | CIT2068F | Stuck in StBy - if switch held in set starts but o | No 10Mhz on pins 31 32 of micro as xtal us | 14-09-04 |
Goldstar | CIT2162X | Int loss of signals | Tuning vots increases to 31v - bad conn on lead between tuner prescaler & tuning pcb | 14-09-04 |
Goldstar | CIT2162X | INT low gain or just snow tuning VOLTAGE AT 30v | INT OC IN LEAD FROM PRESCALER TO TUNING PCB | 14-09-04 |
Goldstar | CIT2162X | Low brightness. | C820 ( 10uF ) | 14-09-04 |
Goldstar | CIT2162X PC08X8 | Dark - only get pic when A1 at max | 180v to vid stage high at 278v; C401 10µ 160v on 112v rail o/c | 14-09-04 |
Goldstar | CIT2168 | Dead | LOPTx shorted turns | 14-09-04 |
Goldstar | CIT2168 | Dead - 118v HT low at 50v | C806S 47µ 160v HT smoothing cap | 14-09-04 |
Goldstar | CIT2168 | Field collapse - int | Pin 5 TDA1170N was 5v instead of 25v. D301 1N4003 faulty. If chip turns out to be faulty use genuine Goldstar chip (others won't work - allegedly) Also check R320 10R 1w | 14-09-04 |
Goldstar | CIT2168 | Int start up | D401 1N4003 o/c in line dr supply | 14-09-04 |
Goldstar | CIT2168 | No start up | Check R811P 22k 3w, D805P R10J in start up cct, C805P 100µ 16v | 14-09-04 |
Goldstar | CIT2168 | Sound muted & goes to Stby after 10mins. | Replace the TDA1940 IC401 remove the link J8 & fit 1k instead. | 14-09-04 |
Goldstar | CIT2168 | Txt absent | Dry joints conn P102 on txt pcb | 14-09-04 |
Goldstar | CIT2168F | Field foldover | C423, C302 100µ 35v | 14-09-04 |
Goldstar | CIT2168F CIT2190F etc | No sound - pic ok - sw to st/by aft 10 mins | Pin 7 IC401 TDA1940 produces muting o/p - chip u/s. Fit 1k res in place of J8 link | 14-09-04 |
|
Goldstar | CIT2170 | Fails to power up from StBy | D/J on main relay : remove retin & replace | 14-09-04 |
Goldstar | CIT2170F | No start up or int sw off | Check for dry joints on main relay | 14-09-04 |
Goldstar | CIT2170F | Patterning from cold | C827 1000µ 25v leaky | 14-09-04 |
Goldstar | CIT2170F | Patterning horiz lines on pic | C827 1000µ 25v - tested ok on esr meter | 14-09-04 |
Goldstar | CIT2172 | Cannot store contrast setting (Too low) | Normal - change R520 to 18k | 14-09-04 |
Goldstar | CIT2172X | No Text after replacing TDA3651. | Must only use TDA as supplied By Goldstar | 14-09-04 |
Goldstar | CIT2172X | Remains in search mode | R80 1M5 high res | 14-09-04 |
Goldstar | CIT2172X CIT2175X | Low contrast at sw on & can't be stored | Replace R520 with 18k | 14-09-04 |