| Make | Model | Problem | Solution | Date |
| | | |
| Found: 1558
|
| Aiwa | C202KER | Field collapse | Fusible link 1500 marked as jumper lead from loptx to reg via D6813 | 14-09-04 |
| Aiwa | CXZR800K | At sw on relay clicks "DEMO" displayed then dead - keeps repeating | Check 2 x 2SK2723 FETs on sound o/p heatsink | 14-09-04 |
|
|
| Aiwa | SE211K | St/by only | R617 high (replace with 390K 1/4W) - located behind LOPTX.This causes the micro-controller to shut the set down and store this condition in the EEPROM. You can either replace the EEPROM with the correct one from Aiwa (which then requires setting up with a special handset), or use an EEPROM programmer to reset the values. There are two values that require resetting:
$0139 should be $00 ($2F when faulty)
$013C should be $00 ($33 when faulty)
| 14-09-04 |
| Aiwa | VX9142K | Dead | R516 270k in psu o/c | 14-09-04 |
| Aiwa | VXD2120K | Pin code resetting when lost | unplug set for 1 hour plus. reduce volume to minimum. simultaneuously press Volume down on unit and "7" to reset pin code and customer ID | 14-09-04 |
| Aiwa | VXG142K | Dead - no st/by | R516 270K, IC501 TDA4605-3, Q500 2SK2397-01MR | 14-09-04 |
| Aiwa | VXG142K | Dead - no stby | R516 270k, IC501 TDA4605-3, Q500 2SK2397 | 14-09-04 |
| Aiwa | VXG142K | Dead with st/by led lit - accepts a tape but no functs | ICP506 1A CP on tv pcb o/c | 14-09-04 |
| Aiwa | VXG142K | Dead with fast tripping aft power cut | C513/C538 1m 160v in psu hi esr | 14-09-04 |
| Aiwa | VXG142K | No pic or vcr mechs - osd & sound ok | Replacing the faulty switching transistor Q511 [2SB926] which supplies the chroma +9V cured both faults. It is situated at the back LHS of the VCR board. | 14-09-04 |
| Aiwa | VXG142K | No sigs | Q1029 (2SC926) at rear of vcr pcb s/c - used a BD234 | 14-09-04 |
| Aiwa | VXT1000 Mk2 | Dead | Ht ok at 120v - ICP1 o/c | 14-09-04 |
| Aiwa | VXT1000 Mk2 | Dead | STK7348 s/c pins 3 & 7, also R103 1R5 3W o/c, R104 27R 3w, R105 1k 1/2w & C90 1µ 50v | 14-09-04 |
| Aiwa | VXT1000 Mk2 | Dead - no line drive | D7 9v1 zener & C105 330µ 16v both s/c | 14-09-04 |
| Aiwa | VXT1000 Mk2 | Failure of IC STK7348 in tv psu | Replace:R102. 33ohmlW Part No S5 34A 330 000 R104 27ohm 3W Part No Sl 330 703 000(6.25UKP) RlOl 33ohm7W Part No Sl 330 862 000(8.37UKP) Also please check and if necessary replace:R103(3.76UKP) R105 Replace as required.
R109(4.00UKP) NOTE: Do not replace IC on its own.<< | 14-09-04 |
| Aiwa | VXT1000Mk2 | Dead | STK7348 psu chip & C88 0.0033pf 2kv | 14-09-04 |
| Aiwa | VXT1000Mk2 | Dead TV sect - vcr sect ok | C88 0.0033µ 1kv burnt; STK7348 psu chip s/c; R109 3R9 7w o/c | 14-09-04 |
| Aiwa | VXT1000Mk2 | No pic sound ok | C88 3n3 1kv burnt | 14-09-04 |
| Aiwa | VXT1000MkII | Sound no picture. | Replace IC4(STK7348) and C88(3n3 1kv). | 14-09-04 |
| Aiwa | VXT1010K | Dead - goes into st/by | R515 3M3 , C517 C526 470uF 10v , C524 47uF 63v | 14-09-04 |
| Aiwa | VXT1010K | Int sw on | Replace STK73907, C514 0µ082 pulse cap, Q501 2SK212, Q510 2SC1815. Change R520 to 68k & C524 to 220µ | 14-09-04 |
| Aiwa | VXT1010K | No cold start up | C524 47µ 10v | 14-09-04 |
|
|
| Aiwa | VXT1400KER | Red weak in pic | Replace C905, 7 & 9 1µ 50v in RGB drives | 14-09-04 |
| Aiwa | VXT1410K | Poor start up from cold, patterning | C522 2µ 50v, C523 100µ 50v | 14-09-04 |
| Aiwa | VXT1420k | Dead | Start up Res R502 1M & R503 820k | 14-09-04 |
| Aiwa | VXT1420K | St/by only | LOPTr leaky | 14-09-04 |
| Aiwa | VXT1450K | Field collapse | FR812 3R9 1w fusible o/c - no other fault found | 14-09-04 |
| Akai | CT1417UK | Field collapse | C411 leaky | 14-09-04 |
| Akai | CT1417UK | FRAME COLLAPSE | C411 LEAKY | 14-09-04 |
| Akai | CT20K2PA | Dark pic - increasing sub brill resulted in field coll | R436 120k o/c | 14-09-04 |