| Make | Model | Problem | Solution | Date |
| | | |
| Found: 50
|
| Alba | CTV14RS/55 | Shows row of dots when vol adj | IC601 MN6030 memory chip faulty | 14-09-04 |
| B & O | LS5000 | St/by only with LED dimming when chan butt pressed | Check connections in metal can under crt neck, esp wickman F1& micro, xtal etc - see Sept 91 TV Mag for article | 14-09-04 |
| B & O | LS5000 | Txt fault - blue blocks darken on lh side | C56 4µ7 25v & check for drys around IC2 on txt pcb | 14-09-04 |
| Granada | C41GS5 CBP1748 | Int sw on | Opto coupler int | 14-09-04 |
| Loewe | MS56 | Startup - no sound or picture. | R534 ( 3.3R ) o/c , check C638 ( 1uf ) | 14-09-04 |
| Loewe | MS56 | This set's picture was marred by very severe Venet | 1k LZ AMP preset P323 had gone open-circuit. | 14-09-04 |
| Loewe | MS56 C8001 | Stuck in standby. | R534 ( 3.3R ) o/c , T534 , C534 ( 47uf ) | 14-09-04 |
| Loewe Opta | MS56 C8001 | Dead. | LOPT SC , R583 OC 22R , IC1581 SC TDA4950 | 14-09-04 |
| Loewe Opta | MS56 C8001 | DEAD STBY LED LIGHT R534 LINE DRIVER FEED OC | REPLACE R534 3R3 T534 C534 | 14-09-04 |
| Lowe | MS56 C8001 | Dead - st/by only | Line dr Tr supply res R534 3R3 o/c also check C534 47µ | 14-09-04 |
|
|
| Lowe | MS56 C8001 | Dead after smelling hot | C652 47µ 250v HT cap leaky/ burnt conns | 14-09-04 |
| Lowe | MS56 C8001 | High HT (should be 142v) | C638 1µ | 14-09-04 |
| Lowe | MS56 C8001 | Venetian blinds | P323 1k LZ AMP preset o/c | 14-09-04 |
| Mitsubishi | HS520V | DEAD | REPLACE R981 IN POWER SUPPLY | 14-09-04 |
| Mitsubishi | HS550V(B) | ROW OF DOTS ON SCREEN | REPLACE CHARACTER GENERATOR IC501 | 14-09-04 |
| Mitsubishi | WS55711 | The WS 55711 will not turn on. The LED on the front will flash when the TV is reset. All the standby voltages are present. It appears the something is telling the processor on the singal board not to turn on the TV. | First check the vertical output IC for poor solder connections and check for leaky capacitors ( look for oily film or dark stuff under and around capacitors, when heated with soldering iron will smell like fish ) I have found many leaky caps on these sets causing shut down problems. | 03-10-05 |
| Nokia | Monoplus 5864 | Lack of width with HT set correct at 109v | Coil LK11 in series with scan coils shorted turns | 14-09-04 |
| Nokia | Monoplus 5864 | To set HT & other menu driven functs | s/c test point XF01 to chassis, enter service mode by pressing Mute, M & TV on handset. Move up/down menus, use vol up/down to change settings. Measure HT at test point X003 | 14-09-04 |
| Salora | 21S5EE Euromono2 | No start up - all psu volts present & LED lights | OC44 (1000uF 16V), a good resorder on line drive circuit & 5C34 (470uF 16V) - 5C36 (220uF 35V) replaced | 14-09-04 |
| Samsung | CI533CN S51A | No sigs - ok thro' SCART | Adj in Factory setting menu - need service manual for info | 14-09-04 |
| Samsung | CI593CN S51A | Dead | C807 2n2 800v burnt, IC801 pt no 1203-001482 faulty | 14-09-04 |
| Samsung | CI593CN S51A | Dead with LED lit green - no line drive | C407 1nF 2kv leaky (next to LOPTr heatsink) | 14-09-04 |
| Samsung | CI593CN3X S51A | No sound/pic - snowy pic/sound available thro' scart o/p | IC902 24W16 EEPROM faulty. Samsung's replacement 24C16 is set on CK tuning system & needs resetting to CI (UK version) Enter serv mode/reset mode to do this or no sound will be present | 14-09-04 |
| Samsung | CI593CN3X S51A | Service mode access | Press St/by, display, menu, mute & power on in sequence, then go to st/by to leave serv mode | 14-09-04 |
| Samsung | S51A | Dead - no line dr | KA7630 reg chip | 14-09-04 |
| Samsung | WI28W6VD S51A | No sound, incorrect width & height | Replaced Eeprom IC902 and reprogram | 14-09-04 |
| Samsung | WI28W6VD S51A | Service mode entering | press the following keys on the remote.
standby>display>menu>mute>power on
option bytes 1. zoom mode: wide/normal/zoom
2. audio mode: nicam stereo 3. one chip: TDA8844
4. led option: normal 5. language: west eng/ger/dut/spa/ita/swe
6. system: CI 7. ats option: on 8. field pol: field pos
having set the option bytes , press menu key and reset message should appear on the screen. | 14-09-04 |
| Sharp | 51FS51H | AGC overload/off tune type fault | Tuner faulty | 14-09-04 |
| Sharp | CS 51CS03H | Long time to come on or reverts to st/by | C714 1000µ 10v & check for dry joints | 14-09-04 |
| Sharp | CS 59/66CS03H | at loud bass sound goes to stby (same on RF or SCART) | sat and cable sound input levels sometimes too high and fool TV into protection mode. No cure, advice customer to reduce volume (ref. Sharp-technical) | 14-09-04 |