Make | Model | Problem | Solution | Date |
| | | |
Found: 62
|
Alba | CTV600 | Int shut down | crack in print near chassis fixing screw (emitter chopper tr to R914 near Q904 heatsink) | 14-09-04 |
Alba | CTV600 | SHUTS DOWN INT | CRACK IN PCB BY MOUNTING SCREW NEAR Q904 HEATSINK | 14-09-04 |
|
Alba | CTV6682 | Blank raster | TDA8362A in prot mode - C707 in field fback volts supply | 14-09-04 |
Alba | CTV6682 | Field coll & no sound | No volts at ramp gen pin 43 TDA8362A; R818 22k o/c | 14-09-04 |
Alba | CTV6682 | Field collapse | R181 22k in 33v supply gone hi | 14-09-04 |
Alba | CTV6682 | Int then dead | chopper tfmr dry joints | 14-09-04 |
Alba | CTV6682 11AK12 | green flyback lines can be seen on the picture, otherwise is Okish | no green output from TDA8362A(2Y), the IC is u/s - caused by intermittently arcing LOPTx (HR6465). | 14-09-04 |
Goodmans | GTV66W 1 11AK19 | Blank raster | small RGB panel on CRT pcb had broken print (not surprising as it gets a lot of physical strain) | 14-09-04 |
Goodmans | GTV66W 1 11AK19 | Bright white raster at sw on then trips off | No volts to TDA6107Q RGB o/p chip on crt base as 47R safety res R914 on base o/c - dry joint on A1 conn of crt base & others probably caused it | 14-09-04 |
Goodmans | GTV66W1 11AK19 | Dead - LOPTx s/c, when replaced, E-W errors | D611 (BY299) was leaky | 14-09-04 |
Goodmans | GTV66W1 11AK19 | E/W dist | Dry joint C613 12nF, R629 27R safety res o/c, C630 390nF 250v low cap | 14-09-04 |
Goodmans | GTV66W1 11AK19 | Narrow pic | C630 dry R629 2.7R burnt. Also replace D612 BY228 | 14-09-04 |
Goodmans | GTV66W1 11AK19 | Tripping | Audio O/P IC TDA2615 | 14-09-04 |
Goodmans | GTV66W1 11AK19B-1 | Width reduced & no E-W | C630, R629 2R7 and the BUK444 200A. | 14-09-04 |
Goodmans | GTV66WI AK19 | Dead with rapid ticking | C630 390nF dry joint, BU2508AF LOPTr s/c | 14-09-04 |
Goodmans | GTV69W3 11AK19 | Switching from Nicam to Mono then no sound | VL301 on Nicam PCB | 14-09-04 |
Goodmans | GTV69W3BLU4 11AK19pro | R629 value | 2R7 in 28" 4:3; 27R in 28" widescreen; 44R in 32" widescreen | 14-09-04 |
Intel | CTV6000 | Dead | Mains fuse o/c; 2x mains rects s/c | 14-09-04 |
NEI | CTV61R | int op | dry joints start up positor & D805 1N4007 | 14-09-04 |
NEI | CTV61R | tuning drift from cold | ZTK33 D001 | 14-09-04 |
Philips | 21PV688 | Dead - safety res R3514 & 3592 o/c & D6524 s/c | Now tripping - TDA6107Q on crt base & FOP chip faulty | 14-09-04 |
Philips | 21PV688 | dead, PSU not running | R3338 39R 0.25W o/c (discharge mains cap first!) | 14-09-04 |
|
Philips | 21PV688 | int. shutting down after frame IC has been replaced | if replaced with later version 6 , also fit frame mof kit 4822 209 16781 | 14-09-04 |
Philips | 21PV688 | No Video remote operation (TV sect ok) | Leave batts out of handset to discharge (several hours) | 14-09-04 |
Philips | 21PV688 | Remote not working | Put in service mode, select 'Service Control' & click 'ok'. Check option codes tally (on label at back of unit). If ok 'Clear' EEPROM | 14-09-04 |
Philips | 21PV688 | Service Mode - entering | Press 'stop' on hset & 'play' on front together for about 5 secs | 14-09-04 |
Philips | 21PV688 | St/by only | Fus res 3514 4R7 3w o/c when TDA8356 IC 7510 fop chip fails | 14-09-04 |
Philips | 21PV688 | tripping, LED flashing red/green | LOPTx u/s (4822 140 10655) | 14-09-04 |
Philips | 21PV688/05 | No pic | No heater supply to crt - R3532 & R3537 4R7 o/c | 14-09-04 |
Philips | 21PV688/05 | Switches to st/by at sw on | Caused by F o/p chip TDA8356 (no heatsinjk compound), also R3512 4R7, R3541 1R | 14-09-04 |