| Make | Model | Problem | Solution | Date |
| | | |
| Found: 100
|
| Philips | Anubis A | Blank raster no sound OSD works signal fed via fro | Unit in External mode check pin 18 IC7015 if high check all jumper leads around scart socket | 14-09-04 |
| Philips | Anubis A | Bright raster with flyback lines. | Break in print on CRT base. | 14-09-04 |
| Philips | Anubis A | Dead - HT being dragged down by LOP stage | Resistance of 20R across LOPTr - LOPTx faulty AT2079/40 -TFHR7488 (CPC) | 14-09-04 |
| Philips | Anubis A | Dead - Ht low at 40v (95v) | Tr7537 sm BC848C error sense tr leaky | 14-09-04 |
| Philips | Anubis A | DEAD , BUT11 SC. | USE SERVICE KIT SBC7021 Pt No Philips 4822 310 20491 | 14-09-04 |
| Philips | Anubis A | Dead apart from whistle | Loptx - tested ok on Oz loptx tester | 14-09-04 |
| Philips | Anubis A | DEAD HT AT ONLY 20v INSTEAD OF 95v IF PLUG M5 REM | D6555 IN 5v SUPPLY LEAKY | 14-09-04 |
| Philips | Anubis A | Dead with HT correct | R3444 5k6 feed to line driver overheating as Driver Tr turned hard on; no lt feed to IC7015 line osc chip TDA4504 from LOP stage as LOPTx faulty | 14-09-04 |
| Philips | Anubis A | Dead with squealing nise - HT only 40v | PSU OK on dummy load - scan coils faulty - reqs replacement of crt also | 14-09-04 |
| Philips | Anubis A | Dead with whine - psu ok on dummy load | Loptx felt warm - faulty | 14-09-04 |
|
|
| Philips | Anubis A | Menu settings | Reqs RC8611 remote. Select last chan by pressing TV+ or -, press VOL/P button on set then press VOL on r/c for more than 4 secs. | 14-09-04 |
| Philips | Anubis A | No HT regulation - R3551 150R sm overheats & Tr7537 BC848C fails | Replace 3 x 36v zeners D6557 -9 & 18v zener D6555. Also LOPTx reqd replacement | 14-09-04 |
| Philips | Anubis A | No sound | In perm mute as Tr7156 BC848 leaky | 14-09-04 |
| Philips | Anubis A | no sound, vision or leds - short squeak at switch on | HT =100v - no line drive or 5v from psu lopt faulty | 14-09-04 |
| Philips | Anubis A | NO TEXT , "E14" ON DISPLAY | XTAL 1701 ON SAA5246 | 14-09-04 |
| Philips | Anubis A | Set works but if a bright sceen pic flickers & H.T | T7554 ( BC337 ) | 14-09-04 |
| Philips | Anubis A | Sound no pic field collapse | TDA3653 field chip dry jointed but resoldering did not cure - replacement did | 14-09-04 |
| Philips | Anubis A | WHEN IN STBY LED FLASHES AND LOUDSPEAKER THUMPS | D6568 6v2 ZENER | 14-09-04 |
| Philips | Anubis A | Dead but blows fuse after repair kit fitted | Crack in print between pin 12 of chopper tfmr & optocoupler | 14-09-04 |
| Philips | Anubis A 14PT155A/05 | Dead - 95V being dragged down because the line dr tr turned hard on by 12V from pin 29 of IC7015 (TDA4504B). | LOPTx | 14-09-04 |
| Philips | Anubis A 52ZY3535 | To exit Demo Mode | Press Prog - & + together at sw on | 14-09-04 |
| Philips | Anubis A AC | Blows BUT11A lop tr int | Dry joints scan coils conn plug | 14-09-04 |
| Philips | Anubis A AC | Dead | C2450 scan coupling cap s/c 330nF in 17/17" CRTs | 14-09-04 |
| Philips | Anubis A AC | Narrow pic 4" wide - rest blanked out | TDA3504 vid contr chip IC7280 | 14-09-04 |
| Philips | Anubis A-AC | Flickers on high brightness with drop in HT | Tr7554 BC337A leaky | 14-09-04 |
| Philips | Anubis A-AC | Ok until put into st/by when LED flashes with thumping noise | D6568 LLZF6V2 leaky in st/by cct | 14-09-04 |
| Philips | Anubis A-AC 17PT166A | Dead - in shutdown mode | s/c across LOPTr coll & emitt - not LOPTx this time but C2450 330nF 250v scan coupling cap s/c | 14-09-04 |
| Philips | Anubis A.AB | "E3" showing at bottom of screen | Cured by replacing EEPROM with a blank | 14-09-04 |
| Philips | Anubis A.AB | Tuning - not stopping when tuning or memorise | Ident pin on micro going leaky - req new micro | 14-09-04 |
| Philips | Anubis A.AC | Blank raster - no sound ,OSD OK | Stuck in AV mode. Pin 18 IC7015 read 3v istead of 0v as Tr7877 never soldered | 14-09-04 |