Make | Model | Problem | Solution | Date |
| | | |
Found: 15
|
Ferguson | TX91 Thomson 10MH73B 10MG73B | dead | SMD TF21 near LOPTx not soldered in factory | 14-09-04 |
Ferguson | TX91 Thomson 10MH73B 10MG73B | dead on 12V supply (car supply) | RD09, RD19 22R 0.5W fusible | 14-09-04 |
|
JVC | AV-14FMG3B | JVC Tv,Model AV-14FMG3B. Power is ok & the power led is light normal. but there is no any picture and sound. it is stuck in standby. the power led is light normal (red ), but the ontimer led (orange) is blinking up to the TV is off. | Resold the vertical I/C. You have dry joints on that part.
| 29-06-05 |
JVC | AV-14FMG3B | Jvc Tv,Model AV-14FMG3B. Power is ok & the power led is light normal. but there is no any picture and sound. it is stuck in standby. the power led is light normal (red ), but the ontimer led (orange) is blinking up to the TV is off. what can be the fault. | Could you check if there is any voltage e.g. on the collector of the high voltage transistor?
A blinking power-led, is usualy indicating a problem on the secundairy side of the power supply!
So try to obtain a diagram and meassure these voltages.
| 02-07-05 |
Nikkai | MG002R | Dead. | R801 ( 1.5R 5W ) o/c by on/off switch. | 14-09-04 |
Philips | 29PT9416 MG7.1 | Service Mode entering | Use the standard remote control and key in a special sequence '0,6,2,5,9,6' followed by pressing the 'MENU' button. If the main menu also appears with the service menu just press 'MENU' again to clear it.. The other way is to short the two service pins on the signal panel (pins 2 and 3 of connector 0356). The advantage of this last method is that all the software protections are turned off. | 14-09-04 |
Philips | MG1.1 28PW6615 | At sw on st/by LED lights then goes amber & starts to flash - in prot mode | St/by relay 4822 280 10375. this is listed as 1P 5V 10A JW1AFSN | 14-09-04 |
Philips | MG1.1E 28PW6615C | poor audio level from rear speakers in dolby mode | remove SMD resistor R3735 located on copper side of LHS of the large signal panel | 14-09-04 |
Philips | MG1.1EAA 32PW6615/025 | Int start up with LED flashing | relay 1002 in psu pt no 2422 1320 7405 | 14-09-04 |
Philips | MG2.1E 28PW9515/05 | Dead with LOPTr s/c - BU2520DF | For reliability do following mod - remove C2411, change C2413 to 10µ 100v, R3406 to 100R to alter line dr coupling from ac to dc | 14-09-04 |
Philips | MG2.1E 32PW9523/05M | Starts up, relays click then shuts down with LEDs flashing | Check relay 1010 - conducts only briefly at sw on in this case | 14-09-04 |
Philips | MG3.1EAA 28PW9525/05 | Sound dist/fuzzy | Hi imp center speaker | 14-09-04 |
Thomson | ICC9 37MG73J | Pic break up with folded horiz lines at bottom half | RF11 safety res 1R5 o/c pt no 15022560 | 14-09-04 |
Thomson | TX807 20MG10C | Sound conversion to 6Mhz | Replace 2 filters Q132 video & Q134 sound for 6 Mhz ones | 14-09-04 |
Thomson | TX807C 14MG15U | Dull pic/low contrast - does vary slightly when adj | RL002 100k ?w o/c in beam lim (in LOP stage) | 14-09-04 |