| Make | Model | Problem | Solution | Date |
| | | |
| Found: 4551 |
| Philips | 28CL6770 | Dead apart from Green LED & "Q" displayed | LOPTx (SEME cheapest) | 14-09-2004 |
| Philips | 28DC2070 D16 | Pic/sound or colour slow to appear at sw on with false line lock | Check electrolytics in IF module | 14-09-2004 |
| Philips | 28ML8762 | Startup intermittent | BUT12A in psu low gain - replace with 2SC3973B | 14-09-2004 |
| Philips | 28ML8770 | Dead | REPAIR PSU WITH SOPS KIT 4822 310 23592 | 14-09-2004 |
| Philips | 28ML8916/05 | Dead with all LEDs flashing | LOPTx (?46+vat) | 14-09-2004 |
| Philips | 28PT7106 | Wrong codenumbers are mentioned in Styling 261. PS 2000-2/3 | In Product Survey's 2000-2 and 2000-3, some wrong codenumbers are mentioned in Styling 261.
See list below for the correct codenumbers:
6a* 3104 328 01612 Cabinet
6c* 3104 328 06051 Cabinet
6d* 3104 328 07142 Cabinet
11a* 3104 | 14-09-2004 |
| Philips | 28PT7306 | Wrong codenumbers are mentioned in Styling 261. PS 2000-2/3 | In Product Survey's 2000-2 and 2000-3, some wrong codenumbers are mentioned in Styling 261.
See list below for the correct codenumbers:
6a* 3104 328 01612 Cabinet
6c* 3104 328 06051 Cabinet
6d* 3104 328 07142 Cabinet
11a* 3104 | 14-09-2004 |
| Philips | 28PW5324/05R | Poor pic with green tint & fb lines | Dry joints LOPTx | 14-09-2004 |
| Philips | 28PW6305 A10 | No Red | IC7301 U/S TDA88858Q. | 14-09-2004 |
| Philips | 28PW6324 | Tripping with st/by LED pulsing | FB tuning cap 1n5 2kv burnt | 14-09-2004 |
| Philips | 28PW6324/05R SA8.0E | Dim raster with sound RGB o/p chip on crt base overheating | Tapping crt neck brought back pic - crt faulty | 14-09-2004 |
| Philips | 28PW6332/05 | No Txt, Scart skts not wotrking, increased height, no zoom, no widescreen etc | Faulty EEPROM, change then go into service default by shorting two T.P out on small signal board, then pressing MENU and - on TV all settings will be self evident. | 14-09-2004 |
| PHILIPS | 28PW6332/05 | VOLUME BARS NOT VISABLE WHEN USING HANDSET | PRESS "MENU" ON TV UNTILL VOLUME BAR DISPLAYED THEN PRESS "I" FOR 3 SEC | 14-09-2004 |
| Philips | 28PW6515/05 | NO raster EHT ok. Int trips if screen volts turned up | D6832 O/C on CRT IN4148 | 14-09-2004 |
| Philips | 28PW6515/05 | R/C inop | Dry joints on IC7064 solder with care dual layered PCB. | 14-09-2004 |
| Philips | 28PW9623 | 28PW9623 was working when I left it, I came back inot the room and there was no picture but the orange LED was flashing constantly. No ticking noise or picture. Does anyone know what this means?
| This fault was caused by a shorted 220pF 2KV capacitor in the line output section | 11-07-2005 |
| Philips | 29DS100 | Unable to switch channel from Pr1 to Pr2. | Check and replace if necessary position 7002 on the SSP into MG21A11.6_01901 (3104 317 41901)
IRIS CODE : 1272 | 14-09-2004 |
| Philips | 29GX1995 AnubisS/BB | Dead | Replaced - Diode 6528 (BZX55) and 6519 (BZX55), Resistor 3503 (1.5R 7W), IC 7510 (UC3842BN) and FET 7513 (H12N60F1). | 14-09-2004 |
| Philips | 29PT5324 | Picture distortion (moire) visible. | Picture distortion (moire) visible in the top of the screen.
Using one of the EXT-inputs, a picture distortion will become visible in the top of the screen as a horizontal bar (Moire-effect). This distortion is more visible when brightness value is betwe | 14-09-2004 |
| Philips | 29PT6021 | SDM does not work by shorting service pins. | Measure pin 19 of SIMM connector 0226 on LSP, if it is 2V (normal is 1V)
then add a resistor of 1K8 between pin 19 of the SIMM connector and
ground. Make sure counting left from pin 1, do not use the pin no. printed
on service print! See attached ph | 14-09-2004 |