datasheet,schematic,electronic components, service manual,repairs,tv,monitor,service menu,pcb design
Schematics 4 Free
Service manuals, schematics, documentation, programs, electronics, hobby ....


registersend pass
Bulgarian - schematics repairs service manuals SearchBrowseUploadWanted

Now downloading free:Rane mx22

Rane mx22 free download

Audio equipment,digital audio, home audio, professional audio systems service manuals and repair information

File information:
File name:mx22sch crossover.pdf
Size:223 kB
Extension:pdf
Mfg:Rane
Model:mx22 🔎
Original:
Descr:mx22 crossover
Group:Electronics > Consumer electronics > Audio
Uploaded:25-11-2009
User:andymac62
Multipart: 0  1

Information about the files in archive:
Decompress result:OK
Extracted files:2
File name mx22man crossover.pdf

OPERATORS MANUAL MX 22 STEREO 2-WAY CROSSOVER QUICK START Whoa, hold on there. Even if you don't read manuals as a matter of principle, at least read this section to avoid hurting yourself or your equipment. Connect the MX 22 with the power off. Balanced XLR cables are recommended, but if you must convert to ¼" connectors, buy or make a cable like the ones on page Manual-11 and keep them as short as possible. This device uses low impedance balanced line drivers. Do not connect the "+" or "­" output pins to ground, as this may cause the power supply to shut down. For unbalanced use, leave the unused output pin ("+" or "­") unterminated. Consult the speaker manufacturer for the correct crossover FREQUENCY setting. As rugged as some drivers are, many (especially compression drivers) will not accept frequencies outside of their normal range without producing distortion and possibly self-destruction. With all equipment turned off and LEVEL controls down, begin making connections to the system as shown on page Manual-4 or 5. When turning on the system, switch on the power amplifiers last. Now, feed the MX 22 some program material. Start by turning up the LOW LEVEL and HIGH LEVEL to the 0 dB marks. Slowly increase the INPUT LEVEL, even if it goes all the way to 10, so the +4 dBu (green) light blinks occasionally and the OL (red) light stays out. This delivers the best signal-to-noise performance. The MONO SUB OUTPUT is a sum of the Left and Right Low Outputs. The MONO SUB LEVEL adjusts only this Output and is not affected by the LOW LEVEL control.. When using a single subwoofer along with full-range cabinets that have internal crossovers, set the 100 Hz FILTER to OUT, allowing the front panel FREQUENCY to control the subwoofer crossover point. When used with biamp cabinets and a subwoofer, set the 100 Hz FILTER switch to IN to allow only frequencies below 100 Hz at this output jack. This way, the MX 22 almost does the job of a Stereo 3-Way crossover, but without removing that awesome bass from the Left and Right Low Outputs. WEAR PARTS: This product contains no wear parts. Manual-1 INPUT LEVEL control and indicators This controls the overall level without altering the relative settings of the Low and High frequency Outputs. Input gain is +6 dB at "10". With signal applied, set this control so the +4 dBu LED lights occasionally, indicating sufficient signal. Flashing of the OL (overload) LED during peaks can be avoided by turning the INPUT LEVEL down. LOW LEVEL control This controls the level of signal going to the LOW OUTPUT jacks. Unity gain is reached at the "0 dB" mark with the INPUT LEVEL set to "10". This control does not affect the MONO SUB OUTPUT level. Refer to Operating Instructions on page Manual-6. MONO SUB OUTPUT, LEVEL trim, and 100 Hz FILTER switch HIGH OUTPUTS These are balanced Output jacks. Connect the LEFT HIGH OUTPUT to the left channel input of the high frequency amplifier, and the RIGHT HIGH OUTPUT to the right channel input
File name mx22sch crossover.pdf

R21 J2 XLR FEM GND C7 330pF TL072 GND R22 1K -15 R35 GND R34 20K GND 20K GND -15 R16 10K 2 5.0V INPUT LEVEL D2 5817 D1 5817 R15 3.74K R18 10K R17 10K C103 1/35 R19 100K GND GND J1 XLR FEM 2 2 1 R23 9.09K 10K R25 1K CW RIGHT INPUT 6 R1B 10KA .4 22/25 2 R27 20K TL072 4 100 .33 Z4A 1 R28 .33 R29 22.1K C10 C11 R24 9.09K 10K GND R26 W11 C9 3 8 Z1B 7 +15 3 + - 5 R31 9.53K C12 .33 R30 150K 5 6 Z4B 7 TL072 W24 .4 RX TO SH. 2 GND +15 1 3 Z3A 4 TL072 -15 R20 10K R D7 8 -15 OL 6 1.0V + 5 R68 1K GND Z3B 7 TL072 R67 10K G D9 +4dBu -15 R4 1K 8 9.09K 10K +15 GND 3 2 4 Z1A 1 TL072 -15 R9 10K W4 .4 R6 R8 LEFT INPUT 1 3 + - CW C1 330pF +15 R1A 10KA GND W10 C3 W9 .4 22/25 .4 R10 20K 3 2 8 1 Z2A 4 TL072 -15 R32 GND 20K R33 20K R11 100 C4 .33 C5 .33 R12 22.1K C6 .33 R13 150K 5 6 R14 9.53K 7 Z2B TL072 W7 .4 LX GND R5 1K 9.09K R7 TO SH. 2 GND GND NOTES (UNLESS OTHERWISE SPECIFIED): 1. ALL RESISTORS 1/4W 1% METAL FILM 2. ALL SWITCHES SHOWN IN THEIR 'OUT' OR 'OFF' POSITION GND CROSSOVER 100458-2.SCH OUTPUTS 100458-3.SCH POWER 100458-4.SCH ACTION: NO CHANGE TO PART, NEW DOC# FJ 14JAN98 DRAWN BY: CHECKED BY: 14-Jan-1998 10802 47th Avenue West Mukilteo WA 98275-5098 SCHEM: INPUTS MX 22 SHEET: H:\MX22\100458-1.SCH SKH RGH 1 of 4 100458 R36 7.15K R37 7.15K C15 RIGHT HP TO SH. 3 .0015 +15 C16 .0015 6 5 TL072 GND C13 470pF GND W29 .4 GND 33.2K R49 511 Z7B 7 15 Z6D R48 13 2 3 14 SSM2164 GND 5 3 6 SSM2164 4 GND C8 470pF 0.1 GND -15 -15 3 GND C28 9 TL072 .4 33.2K R47 511 Z7A 1 W30 2 4 Z6A 8 SSM2164 R43 2 1 8 16 0.1 R42 GND 51.1K 8 C17 .0015 +15 R50 10 1 12 6 Z6C Z8A TL072 33.2K 5 R51 11 SSM2164 511 -15 C14 GND 470pF 4 GND C18 .0015 Z8B TL072 7 FROM SH. 1 R38 RX 20K +15 TL072 1 R39 20K GND R44 R46 30.1K GND 20K 5.11K R45 TL072 2 3 GND -15 4 Z5A 8 6 .4 33.2K R41 511 C2 470pF Z5B 7 7 Z6B W31 R40 5 C27 +15 RIGHT LP TO SH. 3 FROM SH. 1 R77 20K +15 7.15K C23 LEFT HP .0015 +15 6 TL072 6 SSM2164 4 GND -15 R78 20K R83 5.11K R85 30.1K GND 20K R84 GND C19 470pF .4 33.2K R53 511 3 Z14B 7 7 Z11B 5 2 W22 R55 Z12A 1 TL072 .4 33.2K R56 511 C20 470pF GND 8 5 W23 R52 2 TO SH. 3 SSM2164 16 0.1 GND R54 1 51.1K 4 Z11A 3 9 8 GND C30 W27 .4 C29 W13 7.15K .4 R76 R75 LX C24 .0015 6 5 GND -15 0.1 GND W14 .4 Z12B 7 TL072 R57 33.2K R58 511 C21 470pF GND 15 Z11D 13 2 3 14 SSM2164 GND C25 .0015 +15 R59 1 10 Z11C 12 6 Z13A TL072 33.2K 5 R60 11 SSM2164 511 -15 C22 GND 470pF 4 GND 8 C26 .0015 Z13B TL072 7 LEFT LP TO SH. 3 R64 +15 1.91K GND R66 100KB CROSSOVER FREQUENCY R63 + R65 26.7K 3 2 511 C31 10/16 +15 8 1 Z14A 4 TL072 -15 VOLTAGE RANGE = .98V ->0V FRENQUENCY RANGE = 100Hz -> 3.6kHz DRAWN BY: R62 10 + H:\MX22\100458-2.SCH CW GND GND C32 10/16 GND ACTION: NO CHANGE TO PART, NEW DOC# FJ 14JAN98 CHECKED BY: 15-Jan-1998 10802 47th Avenue West Mukilteo WA 98275-5098 SCHEM: CROSSOVER MX 22 SHEET: SKH RWJ 2 of 4 100458 FROM SH. 2 RIGHT HP CW FROM SH. 2 RIGHT LP C61 R140 3 2 20K R141 6.81K GND R142 22/25 CW +15 C46 R114 8 3 2 4 TL072 R120 100K 22/25

>> View document online <<



>> Download document << eServiceInfo Context Help
Attention! This manual is multipart. Download all, before decompressing



Was this file useful ? Share Your thoughts with the other users.

User ratings and reviews for this file:

DateUserRatingComment

Average rating for this file: 0.00 ( from 0 votes)


Similar Service Manuals :
Rane mq15 & mq30 - Rane ge14 & ge27 - Rane fvl22 - Rane gg15 & gg30 - Rane fpl44 - Rane HC4B - Rane HC6 -
 FB -  Links -  Info / Contacts -  Forum -   Last SM download : Beko Beko 12.4-12.5

script execution: 0.02 s