SONY DSC-H2 level 2,3 free download

File name DSC-H2 ver.1.2 L2.pdf

DSC-H2 SERVICE MANUAL Ver. 1.2 2006. 10 Revision History How to use Acrobat Reader LEVEL 2 Internal memory ON BOARD US Model Canadian Model AEP Model UK Model E Model Australian Model Chinese Model Argentina Model Hong Kong Model Korea Model Tourist Model Link SPECIFICATIONS SERVICE NOTE DISASSEMBLY BLOCK DIAGRAMS FRAME SCHEMATIC DIAGRAMS SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST · Precaution on Replacing the SY-150 board Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note : Les composants identifiйs par une marque 0 sont critiques pour la sйcuritй. Ne les remplacer que par une piиce portant le numйro spйcifiй. DIGITAL STILL CAMERA DSC-H2_L2 9-876-937-31 Sony EMCS Co. 2006J1600-1 ©2006.10 Published by Kohda TEC These specifications are extracted from instruction manual of DSC-H2 (2-673-166-11). SPECIFICATIONS Camera [System] Image device 7.18 mm (1/2.5 type) color CCD, Primary color filter [LCD screen] LCD panel 5.1 cm (2.0 type) TFT drive Total number of dots 84 960 (35424 0) dots BC-CS2A/CS2B Ni-MH battery charger Power requirements AC 100 to 240 V, 50/60 Hz, 3W Output voltage 0.5 cm (0.2 type) color AA: DC 1.4V 400 mA Ч 2 AAA: DC 1.4 V 160 mA Ч 2 Total pixel number of camera Approx. 6 183 000 pixels Effective pixel number of camera Approx. 6 003 000 pixels Lens Carl Zeiss Vario-Tessar 12Ч zoom lens f = 6.0 ­ 72.0 mm (36 ­ 432 mm when converted to a 35 mm still camera) F2.8 ­ 3.7 [Finder] Panel Total number of dots Approx. 200 000 dots equivalent Operating temperature 0 to +40°C (+32 to +104°F) Storage temperature ­20 to +60°C (­4 to +140°F) Dimensions Approx. 713091 mm (2 7/8Ч1 3/16Ч3 5/8 inches) (W/H/D) Approx. 90 g (3 oz) [Power, general] Power HR 15/51:HR6 (size AA) Nickel-Metal Hydride batteries (2), 2.4 V R6 (size AA) alkaline batteries (2), 3 V ZR6 (size AA) Oxy Nickel Primary Battery (2), 3 V AC-LS5K AC Adaptor 4.2 V Power consumption (during shooting with the LCD screen) 1.1 W Operating temperature 0 to 40°C (32 to 104°F) Storage temperature ­20 to +60°C (­4 to +140°F) Dimensions 113.28 3.094.0 mm (4 1/2 inchesЧ3 3/8 inchesЧ 3 3/4 inches) (W/H/D, excluding protrusions) Approx. 537 g (1 lb 2.9 oz) (including two batterries, shoulder strap, adaptor ring, lens hood, lens cap, etc.) Electret condenser microphone Dynamic speaker Compatible Mass Exposure control Automatic exposure, Shutter speed priority, Aperture priority, Manual exposure, Scene Selection (7 modes) White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Flash, One push Design and specifications are subject to change without notice. File format (DCF compliant) Still images: Exif Ver. 2.21 JPEG compliant, DPOF compatible Movies: MPEG1 compliant (Monaural) Recording media Internal Memory (30 MB) "Memory Stick Duo" Flash Recommended distance (ISO set to Auto): approx. 0.3 m to 9.0 m (11 7/8 inches to 29 feet 6 3/8 inches) (W)/approx. 0.9 m

File name DSC-H2 ver.1.3 L3.pdf

DSC-H2 SERVICE MANUAL Ver. 1.3 2006. 10 Revision History How to use Acrobat Reader LEVEL 3 Internal memory ON BOARD US Model Canadian Model AEP Model UK Model E Model Australian Model Chinese Model Argentina Model Hong Kong Model Korea Model Tourist Model Link SERVICE NOTE SCHEMATIC DIAGRAMS PRINTED WIRING BOARDS REPAIR PARTS LIST Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note : Les composants identifiйs par une marque 0 sont critiques pour la sйcuritй. Ne les remplacer que par une piиce portant le numйro spйcifiй. DIGITAL STILL CAMERA DSC-H2_L3 9-876-937-11 2006J1600-1 ©2006.10 Published by Kohda TEC Sony EMCS Co. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. Check the B+ voltage to see it is at the values specified. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) 2. 3. 4. 5. 6. : LEAD FREE MARK Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO