datasheet,schematic,electronic components, service manual,repairs,tv,monitor,service menu,pcb design
Schematics 4 Free
Service manuals, schematics, documentation, programs, electronics, hobby ....


registersend pass
Bulgarian - schematics repairs service manuals SearchBrowseUploadWanted

Now downloading free:Konica Minolta 1312ech7

Konica Minolta 1312ech7 free download

Copier office machines (laser, ink-jet,multifunctional devices)

File information:
File name:1312ech7.pdf
[preview 1312ech7]
Size:751 kB
Extension:pdf
Mfg:Konica Minolta
Model:1312ech7 🔎
Original:1312ech7 🔎
Descr: Konica Minolta Copiers 1312 1312ech7.pdf
Group:Electronics > Office equipment > Copiers
Uploaded:31-03-2022
User:Anonymous
Multipart:No multipart

Information about the files in archive:
Decompress result:OK
Extracted files:1
File name 1312ech7.pdf

Chapter 7 Electricity 7-1. Main control circuits ... 7-1 7-1-1. Toner density control ... 7-1 7-1-2. Fusing temperature control ... 7-2 7-1-3. JAM detection ... 7-3 7-1-4. Safety circuit ... 7-4 7-2. Timing chart ... 7-5 7-2-1. A4, TWO COPIES, CASSETTE PAPER FEED (UPPER) ... 7-5 7-2-2. A4, TWO COPIES, CASSETTE PAPER FEED (LOWER) ... 7-5 7-3. Connector list ... 7-6 7-3-1. Main CB (UNIT MAIN) ... 7-6 7-3-2. High voltage unit (UNIT HV) ... 7-9 7-3-3. Power supply board (UNIT PSU) ... 7-12 7-4. IC list ... 7-13 7-5. Test points and VR list ... 7-14 7-6. Electrical parts layout drawing ... 7-14 7-6-1. PCB, lamp (heater), fuse (rating) ... 7-14 7-6-2. Clutches (solenoid) and motors ... 7-15 7-6-3. Sensors and switches ... 7-15 Chapter 7 Electricity 7-1. Main control circuits 7-1-1. Toner density control 1. Toner density detection The TNS signal detected by the toner sensor is relayed by the high voltage unit (UNIT HV) and connected to CN191-20 on the main CB (UNIT MAIN). After the TNS signal is changed to a partial voltage (TNS! signal) by the registance in the main CB, it is input into the IC121 (CPU) pin No. 77. The TNS! signal can be measured with the test point (TP103). 1 2. Toner motor drive control As the toner is consumed and the toner density becomes lighter than the optimum density, the TSM signal is output (HIGH -> LOW) from the IC121 No. 23 pin. The drive circuit in the high voltage PCB (UNIT HV) is acti- vated to rotate the toner motor (pulse motor) and supply the toner. Supply time: 3.5 sec. 1 3. Forced toner supply mode If the toner sensor detects a light density 1% less than the optimum density three times in succession, this unit will stop the copy operation, and forcibly supply toner. During this mode's operation, P25 will display (forcibly supplying toner).time: Max. 250 sec. When the toner density is recovered (6.5%), the stopped copy job will automatically resume. However, if the density is not recovered, P25 will blink (toner empty), and after 30 copies, the copy operation will stop. 4. Initialization of developing unit When the unit's power is turned on in the unused state (when installed), P26 will light (developer not initialized), and the standby state will not b

>> View document online <<



>> Download document << eServiceInfo Context Help



Was this file useful ? Share Your thoughts with the other users.

User ratings and reviews for this file:

DateUserRatingComment

Average rating for this file: 0.00 ( from 0 votes)


Similar Service Manuals :
Konica Minolta 1312ech5 - Konica Minolta 7020SF0E - Konica Minolta FS107AWE - Konica Minolta FK116V1E - Konica Minolta F107E - Konica Minolta D314E - Konica Minolta D314AWE -
 FB -  Links -  Info / Contacts -  Forum -   Last SM download : AIWA aiwa hs-jx505

script execution: 0.01 s