| Make | Model | Problem | Solution | Added | Date |
| | | | |
| Found: 711 |
| Sharp | 51DT-25H | Lines across screen when cold | C604 220u 10v | plamensl | 14-09-2004 |
| Sharp | 51DT-25H CA1 | Stuck in st/by with motorboating from spkr | C712 220µ 16v in 10v supply almost o/c | plamensl | 14-09-2004 |
| Sharp | 51DT25H | Dead - no st/by | R705 560k o/c, also replaced R704 560k | plamensl | 14-09-2004 |
| Sharp | 51DT25H | Going off tune picture blanks etc | C715 470mfd 10v o/c | plamensl | 14-09-2004 |
| Sharp | 51DT25H | int blank raster, lack of height, off tune | Fit D511 & 512 3v6 zeners in marked places next to IC201, fit D403 by plug K - replace link 122 in 5v supply with 12µ coil. | plamensl | 14-09-2004 |
| Sharp | 51DT25H | Int lack of height or off tune when 1st sw on - ok at subsequent sw on | Sharp mod - add 3.6v zener between pin 63 IC201(cathode) & chassis; add another 3v6 zener pin 64 & chassis(cath to chip). Substitute link J122 with 12uH coil pt no VP-CF120K0000; Add 7v5 zener pin 30 (cath) & chassis. Check CRT final anode for cleanliness | plamensl | 14-09-2004 |
| Sharp | 51FS51H | AGC overload/off tune type fault | Tuner faulty | plamensl | 14-09-2004 |
| Sharp | 56FW-53H | Dead & E/W problems | LOPTr BUH515 leaky, C613 SH1010 - CHS dry jointed & o/c - cause of problem, L603 RCILP0286BMZZ, Q506 RHTX0151BMZZ(2SD2391Q) sm E/W Tr, R613 3k3 3w, D516 47v zener | plamensl | 14-09-2004 |
| Sharp | 56FW-53H DA50W | E/W faulty | C613 560nF 250v o/c in LOP stage | plamensl | 14-09-2004 |
| Sharp | 56FW53H | Blows LOPTr int at sw on | C607 330µ in line driver | plamensl | 14-09-2004 |
| Sharp | 56FW53H | Dead - LOPTr s/c | Fit new BUH515, check for dry joints C613 & C607 330µ 10v hi esr | plamensl | 14-09-2004 |
| Sharp | 56FW53H | Lines of R, G & B at top of screen & pin cush dist at top | Need to set up NVM values for specific crt type obtained from Sharp Tech bulletins. Also may need to alter geometry settings in service mode. | plamensl | 14-09-2004 |
| Sharp | 56FW53H | No audio | IC302 (TDA7480) l/h audio o/p Ic (about 8ukp from Seme) and two chokes connected to it L315/L316 (3.3microH) (about 1.50ukp packet of 5 from Farnell) were burnt to a crisp.After replacement I still had no l/h audio, found Q306 (2SC2412 sm) s/c in the +5v feed to the Ic (I used a BC847) | plamensl | 14-09-2004 |
| Sharp | 56FW53H | Service mode access | Switch on with vol down & Ch up buttons pressed. The ch up/down & vol up/down buttons on the handset are used to alter values & each setting must be stored by pressing St/by | plamensl | 14-09-2004 |
| Sharp | 59CS-D8H | Various inc slow start up, Txt int appears, buzz on sound | C714 1000µ 16v in 5v supply | plamensl | 14-09-2004 |
| Sharp | 59CS03H | Audio noise - int | Q305/306 | plamensl | 14-09-2004 |
| Sharp | 59CS03H | Dead | TDA8375A IF/video proc/tbase chip faulty IC201 (low res between pin 56 & Chassis) | plamensl | 14-09-2004 |
| Sharp | 59CS03H | Dead & whistling | Q306 2SA1797Q sm audio amp s/c - also check Q306, D301/2, D305 1N4933 & check for dry joints back of scan coil pcb | plamensl | 14-09-2004 |
| Sharp | 59CS03H | Field lin creeps up at bottom | Q707 C33840 = BC338-40 | plamensl | 14-09-2004 |
| Sharp | 59CS03H | No / int field collapse | Resolder L501 ( joints on body ) | plamensl | 14-09-2004 |