| Make | Model | Problem | Solution | Added | Date |
| | | | |
| Found: 711 |
| SHARP | 66CS03H | FRAME BOUNCE WITH ROLL ON TEXT | REPLACE C604 330MFD10V | plamensl | 14-09-2004 |
| Sharp | 66CS03H | INTERMITTANT BLOWING OF Q601/Q701 | REPLACE C604, R638 AND R641 | plamensl | 14-09-2004 |
| Sharp | 66CS03H | Line o/p tr BUH515 int blows at sw on | C604 330µ 10v | plamensl | 14-09-2004 |
| Sharp | 66CS03H | Out of focus col blobs in raster & no sound | 45v to fop & audio stages missing. R643 5R6 o/c & D623 10v zener cooked but R643 overheats when sw on. Remove Q509 (fop feed) ; no -13v at Q508 emitter as R631 o/c; ok when former replaced | plamensl | 14-09-2004 |
| Sharp | 66CS03H | SLOW START FROM COLD | REPLACE C714 1000MFD10V | plamensl | 14-09-2004 |
| Sharp | 66CS03H | St/by only | Ripple on 5v supply caused by C714 1000µ 10v low cap | plamensl | 14-09-2004 |
| Sharp | 66CS05 | Field top cramp when cold | C517 22µ | plamensl | 14-09-2004 |
| Sharp | 66CS05 | Long time to come on | C714 1000µ | plamensl | 14-09-2004 |
| Sharp | 66CS05 | No sound/pic but dull raster with purity type errors | R631 (not a resistor but a fuse)- D623 10v zener sm & R643 5R6 | plamensl | 14-09-2004 |
| Sharp | 66CSD8H | Service mode entering | PRESS CH+ AND VOL- AND SWITCH ON | plamensl | 14-09-2004 |
| Sharp | 66DS-03H CA10 | Dead - psu blown up due to faulty opto coupler | Replace Q702, 703 etc & opto - careful not to overheat it when soldering new one in or hi HT persists See Sharp Tech bulletin CTV20010101 | plamensl | 14-09-2004 |
| Sharp | 66DS03H | Field collapse then dead | C613 dry joints | plamensl | 14-09-2004 |
| Sharp | 66ES03 | Dead still, after psu & LOP stage rebuild | C607 330µ in psu sec & check other caps in the region | plamensl | 14-09-2004 |
| Sharp | 66ES03 | Field collapse | F601,F602,Q501,Q502 | plamensl | 14-09-2004 |
| Sharp | 66ES03H | Service mode entering | Vol down & Channel up at switch on - go to st/by to store | plamensl | 14-09-2004 |
| Sharp | 66FW-53H DA100 | Dead - LOPTr s/c, C720 100µ 200v split open | opto-coupler (IC705) and the two damaged components above (Q601 & C720). Fit avalanche diode across C720
to prevent future damage (cathode to positive). A new TEA5101A (IC1801) was also fitted on the CRT panel as a precaution | plamensl | 14-09-2004 |
| Sharp | 66FW-53H DA100 | Stuck in standby ,only orange LED | Replace opto coupler IC705, Q601 (BUH 515), Q5408 / Q5407 and R5425 (470ohm) on tube base. C720 (200V/100uf.) Add avalanche diode RH-EX0875BMZZ across C720 | plamensl | 14-09-2004 |
| Sharp | 66FW-53H DA50W | LOPTr BUH515 fails at sw on | Check for dry joints in line driver & o/p stages & replace C607 33025v in driver | plamensl | 14-09-2004 |
| Sharp | 66FW53H | Dead with bang | C720 blown, R765 & 766 100R sm o/c, R623 1R o/c & Q601 BUH515 s/c, caused by opto IC501 MOC8106 | plamensl | 14-09-2004 |
| Sharp | 66FW53H | LOPTr repeated failure | LOPTx faulty | plamensl | 14-09-2004 |