| Make | Model | Problem | Solution | Added | Date |
| | | | |
| Found: 711 |
| Sharp | CA10 66DS03H | STUCK ON 1 CHANNEL, NO REMOTE OR FRONT FUNCTIONS | REPLACE R705 68K | plamensl | 14-09-2004 |
| Sharp | CA10 66DS05H | Field lin problems | Check F601/2 o/c | plamensl | 14-09-2004 |
| Sharp | CA10 66DS05H | INTERMITTENT STANDBY AT HIGH VOLUME | CHANGE VALUE OF C335/C336 TO 022MFD | plamensl | 14-09-2004 |
| Sharp | CA10 66DS05H | St/by only | BUH515 lop tr s/c due to dry joint C613 0µ68 250v | plamensl | 14-09-2004 |
| Sharp | CA10 66DS05H | St/by only - shuts down aft 2 secs | Check spkr is connected & ok (will not run if dis'd) | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Dead | Dry joint C613 680nF 250v &/or o/c, LOPTr s/c or overheating, R613 2k2 2w o/c pt no VRS-VV3DB222J | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Dead | R713 (and/or) R714 in PSU o/c. (Both 560K) | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Dead - blow up after dry joint on C613 | Q701 2SK2605; Q702 BC338; Q703 BC338; Q602 BUH515 line o/p tr; D712 BZX79C15; D713 1N4148; R716 .R.47 1 WATT CIRCUIT SAYS R.22 BUT THE ORIGINAL WAS R.47; R717 22K; R719 22O OHM; C713 68 NFD.; FUSE 3.15a | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Dead - blows Q701 Q702 Q703 D712 D715 at switch on | Change Q701 BUZ90, Q702 & Q703 BC338, R722 33R smr.R716, R61, D715 & D712. I/C 901 TDA6107 on tube base. D712 15volt zener not marked as zener on print. | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Dead - chopper Tr s/c | Replaced along with 2 x mains rects, R716 0R22, Q702 & Q703 + dry joints LOP | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Dead LOPTr s/c | Dry joint C613 check/resolder line scan coil conns | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | dead, neon light on | R713, R714 560k start up resistors o/c | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | dead, no line drive and smell of burning | no 8V supply, D712 1N4935 s/c | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Field - only half a scan | Check FOP Trs Q501 & 502 sm FET types TX00171BMZZ & TX00172BMZZ also cprot F601 2.5mA | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Field faulty | Check F601 & F602 | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Lack of width & LOPTx runs hot | C608 low cap | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Locked up - no response from front controls or R/C | R704 / R705 both 68k 1 W | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Remote & front controls inop | R704 R705 68k (at the front of the pcb) | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | Ringing/noises from psu after component replacement following dry joint C613 | replace both new bc338/40 with Sharp versions | plamensl | 14-09-2004 |
| Sharp | CA10 66ES03H | St/by only | R704/705 or R713/714 | plamensl | 14-09-2004 |