Information about the files in archive: |
Decompress result: | OK |
Extracted files: | 76 |
File name | | Text |
ARE001.PDF | | Date : Feb. 23, 1995 DIGITAL COPIER : AR-5040 No. : ARE-001
PARTS CHANGE AND ADDITION
1.Model name: AR-5040
2.General:
There have been changes and additions of parts in the model above from the start of mass production.
3.Description:
1. Addition of CCD protection sheet to CCD cover in the scanner unit
CCD protection sheet (added)
CCD cover (P/G 12 -28)
2. Parts' code change in the fiber fixing cushion of the scanner unit
3. Addition of FIN positioning spacer to the chassis joint plate in the finisher section
1/4
Green C
SHARP CORPORATION
Reprography Division
Rear
Chassis joint plate (P/G 48 )
, ,
Front Standard
FIN positioning spacer (added)
Standard
4. Parts' code change of TC spring of TC-AC case unit
5. Addition of polyslider and discontinuance of screw in the waste toner box unit
A screw discontinued
Polyslider (added)
6. Change of screws and discontinuance of open detection lever in the finisher unit
2/4
,, ,
0~1mm
7. Addition of a shield seal agai |
ARE002.PDF | | Date : Jun. 16, 1995 DIGITAL COPIER : AR-5040 No. : ARE-002
NOTIFICATION OF CHANGED PARTS AND NEW PARTS ADDITIONS.
1.Model name: AR-5040
2.General:
Changes in parts codes and the addition of new parts have been carried out in the model listed above from the start of mass production and are hereby reported.
3.Description:
1. Change in the 100MXL belt in the finisher delivery guide frame unit. 2. Addition of protective sheets A and B for the PG edge on the upper surface of the delivery guide of the finisher delivery guide frame unit.
Standard
PG edge protective sheet A
Upper surface of the delivery guide (P/G 57 -5)
PG edge protective sheet B
3. Addition of delivery guide mylar to lower edge B of the delivery guide in the finisher delivery guide frame unit.
Delivery guide mylar
1/6
Green C
SHARP CORPORATION
Reprography Division
4. Addition and resetting of AC cord. 5. Addition of parts and change in the screws of the conveyor guide unit in the front and rear frames.
Front |
ARE003.PDF | | Date : Apr. 21, 1995 DIGITAL COPIER : AR-5040 No. : ARE-003
1. 2. 3. 4. 5.
STANDARDIZATION OF THE PARTS CODES FOR THE IC IN THE ICU PWB. PREVENTION OF NOISE IN THE SHIELD BOX. CORRECTION OF THE PARTS GUIDE. DISCONTINUANCE OF THE SHIELD MYLAR IN THE SHIELD BOX UNIT TO IMPROVE PRODUCTIVITY. PREVENTION OF UNCLEAN COPIES DUE TO THE CURLING OF THE REAR END OF THE COPY PAPER DURING DOUBLE SIDE COPY OPERATIONS. 6. IMPROVEMENT OF PUSHER OPERATIONS IN THE FINISHER UNIT.
1. Standardization of the parts codes for the IC in the ICU PWB. 1.Model name: AR-5040
2.General:
An error for the parts codes of the IC (Silk No. IC 33) used in the ICU circuit board was found, listing two different model codes for the same part. To correct this error the parts codes have been standardized as described below.
3.Description: VHISN74LS19NVHISN74LS19NS These are the same IC, but the parts codes are listed as different models.
The parts codes have been standardized and listed as: VHISN74LS19NS
4.Action:
|
ARE004.PDF | | Date : Aug. 21, 1995 DIGITAL COPIER : AR-5040 No. : ARE-004
1. CORRECTION OF PARTS CODE ERROR. 2. ADDITION OF A SHEET TO COVER THE ELEVATOR MOTOR TO PREVENT THE INFILTRATION OF FOREIGN MATTER.
1. Correction of parts code error. 1.Model name: AR-5040.
2.General:
An error in a portion of the parts codes listed in the parts guide has been found, and correction of the error is requested.
3.Description: Parts guide No. 74 -28
Error LX-BZ0198FCZZ 1st mirror Adjusting screw
Correction LX-BZ0108FCZZ Silicon blade screws
2. Addition of a sheet to cover the elevator motor to prevent the infiltration of foreign matter. 1.Model name: AR-5040.
2.General:
There was a possibility of infiltration of foreign matter through the opening section above the staple tray in the finishing unit. If by chance metallic matter happens to infiltrate into the elevator motor there is a possibility that it may come in contact with the terminals of the motor. To alleviate this problem, a cover sheet has been |
ARE006.PDF | | Date : Nov. 15, 1995 DIGITAL COPIER : AR-5040 No. : ARE-006
CHANGES AND ADDITIONS OF PARTS
1.Model name:
AR-5040.
2.General:
Changes and additions of parts have been carried on the machine listed above, and are hereby reported.
3.Description:
(1) The metal pattern of the DSD collar (P/G 17 -52) used in the DV box unit is interchangeable with that of models SF-9400/8870/8800, and the parts code for models SF-9400/8870/8800 is printed on the side face. This is confusing however, and to alleviate the potential of problems due to confusion, the printing has been discontinued and the DSD collar for model AR-5040 is now marked with black to distinguish it. (As is listed in the parts guide, the parts code for model AR-5040 is different from the parts code for models SF-9400/8870/8800.) (2) The black electro deposition used for the surface finishing of the CCD cover of the scanner unit has been changed to black galvanization in order to decrease the noise from the power supply. In addit |
ARE007.PDF | | Date : Apr. 16, 1996 DIGITAL COPIER : AR-5040 No. : ARE-007
CHANGES AND ADDITIONS OF PARTS.
1.Model name: AR-5040
2.General:
Parts changes and additions have been carried out on the models listed above, and are hereby reported.
3.Description:
Price rank Effec- Intertive changetime ability
Version
P/G No.
Old parts code
New parts code
Parts name
Reason for changes
46 -15 46 -16 All 46 -14 46 46 -901 49 -52 49 -53
PGIDH0947FCZZ PSHEP1930FCZZ PSHEP1968FCZZ -- CCASZ0269FC51 PSHEZ3734FCZZ Discontinuance -- PSHEP3735FCZZ CGIDH1598FC01 CCASZ0269FC52 AS BF Discontinuance --
TC Guide TC Guide mylar TC sheet TC front PG SE AS TC-AC case unit N ST cover sheet ST cover sheet 200 ST cover sheet SEI Washers FG mesh lines See text 1st lot `95/2 3 Carried out in accordance with a request from EMI. Carried out as an improvement measure for drive load changes. Carried out as an improvement measure for curling during double-side copy operations. 1st lot AA Screws Changes have been carried ou |
ARE008.PDF | | Date : Apr. 10, 1996 DIGITAL COPIER : AR-5040 No. : ARE-008
CHANGES AND ADDITIONS OF PARTS.
1.Model name: AR-5040
2.General:
Parts changes and additions have been carried out on the models listed above, and are hereby reported.
Price rank Effec- Intertive changetime ability
Version
P/G No.
Old parts code
New parts code
Parts name
Reason for changes
57 -13
NPLYZ0183FCZZ LPINS0096FCZZ LX-WZ0011FCZZ
NPLYZ0087FCZZ LPINS0155FCZZ Discontinuance MSPRC2124FCZZ
AB AA -- AC
Paper discharge pulley (large) Pin Washer FIN paper guide spring F FIN paper guide spring R Sheet 1st lot `95/4
1
MSPRC2125FCZZ All 57 -- PSHEP3618FCZZ (Q`ty: 2)
AD
Carried out as a measure to improve the stacking performance of the finisher. --
AA LX-WZ0017FCZZ (Q`ty: 2) PSHEP3850FCZZ (Q`ty: 2) -- Discontinuance -- Washer FIN paper guide upper B sheet B FIN paper guide upper B sheet C LED 1st lot `95/7 1 Carried out as an improvement measure to prevent the LED from becoming misaligned. Carried out as an im |
ARE010.PDF | | Date : Mar. 28, 1996 DIGITAL COPIER : AR-5040 No. : ARE-010
REGARDING 500 CASSETTE PAPER FEEDING UNIT USE AND THE PERIOD FOR CHANGING THE ROLLERS
1.Model Name: AR-5040
2.General:
We are changing the 500 cassette paper feeding unit used by the above models to that of the SF-2025/2030/2040, so that the two units now use the same unit. For more details, please see the appended sheet. When parts of the old unit are changed, new parts will have to be used, so we request that you change and add the necessary new parts all at once. The paper feeding roller, reverse roller, and drawing roller for the SF-2025/2030/2040's paper feeding unit are listed in the service manual as requiring changing when made 80K or after 2 years. This note is not included in the service manuals for the models listed above, but we ask that you change the parts when the unit is made 80K or after two years as listed above.
3.Description:
Old New NROLR1114FCZZ NROLR1049FCZZ NROLR1093FCZZ NBRGP0549FCZZ NBRGP0550FCZZ |
ARE011.PDF | | Date : May. 14, 1996 COPIER : AR-5040 No. : ARE-011
(Service Information)
ABOUT HANDLING THE DIP SW
1.Model Name: AR-5040
2.General:
We are adding instructions on making adjustments to the above models, and also changing the handling procedures for the DIP SW of the RADF control PWB as indicated below.
AR-5040 General view of the control PWB OFF ROM ON DIP SW CPU PUSH SW
General view of the DIP switch
SW No.1
2
3
4
5
1/2
Green C
SHARP CORPORATION
Reprography Division
Adjust ments to the ADF Please carry out the following three adjustments whenever changing any of the RADF/ADF sensors.
No. 1 2 3 Adjustment Initializing the E2PROM Adjusting each sensor Original halt position adjustment Part adjusted Adjustment in ADF unit mode Adjustment in ADF unit mode Adjustment using Sim. 53 of the copier unit
ADF unit mode (E2PROM/sensor) adjustment procedure Before making adjustments... Open the ADF back side maintenance cover.
Turn the copier off
DIP SW settings
While pressing |
ARE012.PDF | | Date : Jul. 30, 1996 DIGITAL COPIER : AR-5040 No. : ARE-012
CHANGES AND ADDITIONS TO PARTS.
1.Model Name: AR-5040
2.General:
We have made changes and additions to parts of the above model.
Current parts Ref. No. Model name Version P/G No. Parts code 10 -15 1 AR-5040 All 39 -901 DUNTM6554FC11
New parts Parts code Price rank Parts name
Effec- Intertive changetime ability
Reasons for changes
DUNTM6785FCZZ
BE
Lift up unit
1st lot '96/2
1
In order to improve productivity, we are making the part the same as that for the SF-2025/2030/2040. Due to improvements in the harness attachment, we are adding this to the drive joint plate (P/G 10 -6 ).
2
AR-5040
All
10
--
LHLDW6655RCZZ
AB
Cable holder
1st lot '96/1
6
SHARP CORPORATION
Reprography Division
Green C
|
ARE013.PDF | | Date : Oct. 22, 1996 DIGITAL COPIER : AR-5040 No. : ARE-013
THE ADDITION OF A SEPARATOR PAWL SPACER TO THE DRUM CLEANER UNIT.
1.Model Name: AR-5040
2.General:
The separator pawl in the drum cleaner unit does not always detach from the drum. To prevent this problem, we have made the changes described below.
3.Description:
Please attach a separation pawl spacer to the cleaner unit as indicated below.
Separation pawl spacer
4.Action:
From the first unit of May, 1996 production.
Current parts Ref. No. Model name Version P/G No. Parts code
New parts Parts code Price rank AC Parts name
Effec- Intertive changetime ability 1st lot '96/5
Note
1
AR-5040
All
18
--
PSPAZ0704FCZZ
Separation pawl spacer
6
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 4. Not interchangeable. 5. Interchangeable i |
ARE014.PDF | | Date : Nov. 5, 1996 DIGITAL COPIER : AR-5040 No. : ARE-014
CHANGE IN THE ROLLER FRAME IN THE FINISHER ELEVATOR FRAME UNIT.
1.Model Name: AR-5040
2.General:
There was a danger of the sensor and the roller frame F in the finisher elevator frame unit coming in contact with each other. To alleviate this problem the roller frame F has been changed into one that is divided into two parts.
(Old)
Roller frame F Changed
CFRM-0781FC01 CFRM-0781FC02 LPLTM5319FCZZ XBBSD30P08000
Q'ty: 1 Q'ty: 1 Q'ty: 1(added) Q'ty: 2(added)
(New) Roller frame F Sensor light shield plate M3 x 8
(Assembly procedure) Changed Roller frame F CFRM-0781FC02 Sensor light shield plate LPLTM5319FCZZ
The screw should be driven so that the sensor light shield plate is positioned in the center portion of the sensor detection area.
Roller frame F CFRM-0781FC01
sc scr rew ew M When fixing the screws, 3× the screw lock should be applied. Q'ty: 8bin 2 d
3.Action:
From 1996 August production.
1/2
Green C
SHARP CORP |
ARE016.PDF | | Date : Nov. 28, 1996 COPIER : AR-5040 No. : ARE-016
1.MEASURE TO ALLEVIATE PROBLEMS OF DIAGONAL FEEDING FROM THE UPPER PAPER CASSETTE. 2.CHANGE IN THE MANUAL PAPER FEEDING LEVER IN THE MANUAL MULTI PAPER FEEDING UNIT AS A MEASURE TO IMPROVE PRODUCTIVITY.
1. Measure to alleviate problems of diagonal feeding from the upper paper cassette. 1.Model Name: AR-5040
2.General:
A change has been carried out in the shape of a portion of the U-turn paper guide in the transport unit. In accordance with this change, a change has been carried out in the part code. These changes have been carried out as a measure to alleviate problems of diagonal feeding from the upper paper cassette.
3.Action:
Japanese production: Chinese (SOCC) production:
Running change from 1996 mid-July production. Running change from 1996 mid-October production.
2. Change in the manual paper feeding lever in the manual multi paper feeding unit as a measure to improve productivity. 1.Model Name: AR-5040
2.General:
A |
ARE017.PDF | | Date : Mar. 5, 1997 DIGITAL COPIER : AR-5040 No. : ARE-017
CHANGE IN THE ORIGINAL COPY DETECTION SHIELD OF THE OPTICAL UNIT CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY.
1.Model Name:
AR-5040
2.General:
A change has been carried out in the shape of the original copy detection shield in the optical unit of the models listed above. This change has been carried out as a measure to improve productivity. In accordance with this change, the shield sheet has been discontinued.
3.Description:
Original copy shield sheet Original copy shield
PSHEP3915FCZZ PSLDH0170FCZZ
Discontinued PSLDH0178FCZZ
4.Action:
From 1996 November production.
Current parts Ref. No. Model name Version P/G No. Parts code 3 -8 1 AR-5040 All 3 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. PSHEP3915FCZZ PSLDH0170FCZZ
Ne |
ARE028.PDF | | Date : Jun. 13, 1997
DIGITAL COPIER : AR-5132
No. : ARE-028
CHANGE IN THE BEARING OF THE CASSETTE RAIL CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY .
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the maker of the cassette rail caulked bearing of the cassette rail L/R in the cassette unit. This change has been carried out as a measure to improve productivity.
3.Action:
From 1997 April production.
Current parts Ref. No. Model name Version P/G No. Parts code 30 -16 CRALM0110FC01 48 -27 AR-5132 Overseas 30 -7 CRALM0111FC01 48 -7 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type.
New parts Parts code Price rank Parts name
Effec- Intertive changeability time
Note
CRALM0110FC02 AP CRALM0111FC02
Cassette rail R 1st lot '97/4 Cassette rail L 1
4. Not interchangeable. 5. Interch |
ARE041.PDF | | Date : Jun. 26, 1997
DIGITAL COPIER : AR-5040
No. : ARE-041
[Service Information]
ESTABLISHMENT OF SCANNER UNIT AS ASERVICE PART.
1.Model Name:
AR-5040
2.General:
The lens base unit and the scanner base unit had been established as separate service parts, but adjustment operations are very difficult when the two parts have been assembled in the markets. As a measure to alleviate this problem and improve service conditions, the combination of these two parts into a single unit has been carried out and the new single unit has been established as the scanner unit.
3.Description:
A Lens base unit: CDAIU0498FC51 (P/G 12 -501) B Scanner base unit: CDAIU0490FC51 (P/G 12 -502) A + B = Scanner unit: DUNT-6719FC30 (for the 100 V series) DUNT-6719FC31 (for the 200 V series)
Current parts Ref. No. Model name Version P/G No. Parts code 100V Series AR-5040 200V Series 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of cur |
ARE043.PDF | | Date : Jul. 7, 1997
DIGITAL COPIER : AR-5132
No. : ARE-043
1. MEASURE TO ALLEVIA PROBLEMS OF ELECTRICAL TE NOISE. 2. MEASURE TO ALLEVIA PROBLEMS OF JAMS WHICH TE OCCUR BEFORE THE FUSING PROCESS.
1. Measure to alleviate problems of electrical noise.
1.Model Name:
AR-5132 (Only for machines bound for the destinations of the 200 V series).
2.General:
The changes and additions of the parts listed below have been carried out as a measure to alleviate problems of electrical noise in machines bound for destinations of the 200 V series.
3.Description:
<1> Agrounding plate right has been attached to the left side of the rear frame.
M3 screw type speed nut ø2 hole M3 × 6 bind taping, 2 types
Abnormally shaped hole
Rear frame left side
Corner Screw tip standard B'
Square hole
Grounding plate right
M4 screw type speed nut
ø5 hole M4 × 6 bind taping, 2 types Dimple
1/3
Green C
SHARP CORPORATION
Reprography Division
<2> Agrounding plate left has been attached to the fusing drawer at |
ARE044.PDF | | Date : Jul. 1, 1997
DIGITAL COPIER : AR-5040
No. : ARE-044
1.MEASURE TO PREVENT THE CL LEAD WIRE FROM LIFTING UP . 2.MEASURE TO PREVENT CONTACT WITH THE HOME POSITION SENSOR DETECTION PLA IN THE SCANNER UNIT. TE
1. Measure to prevent the CL lead wire from lifting up.
1.Model Name:
AR-5040
2.General:
ACL lead wire cover has been added as a measure to prevent the CL lead wire from rising up.
CL Lead wire cover Insert into the screw hole
Tighten together with the step screw
3.Action:
From the start of 1997 April production.
2. Measure to prevent contact with the home position sensor detection plate in the scanner unit.
1.Model Name:
AR-5040
2.General:
The ground wire from the ORS illumination PWB is fixed to the optical plate, but the fixing screws were too long, creating the possibility of contact between the ground wire fixing screw and the detection plate of the home position sensor occurring during scanner unit operations. As a measure to alleviate this problem, sufficien |
ARE045.PDF | | Date : Jul. 10, 1997
DIGITAL COPIER : AR-5132
No. : ARE-045
[Service Information]
CHANGE IN THE CPU OF THE MIRROR MOTOR CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY .
1.Model Name:
AR-5132
2.General:
The CPU of the mirror motor (P/G 4 -28) has been changed from a one time type to a mask type. This change has been carried out as a measure to improve productivity. Furthermore, in accordance with this change the CPU socket has been discontinued. Note: The old part and the new part are interchangeable, and therefore no change has been carried out in the part code.
3.Action:
From 1997 June production.
SHARP CORPORATION
Reprography Division
Green C
|
ARE046.PDF | | Date : Aug. 1, 1997
DIGITAL COPIER : AR-5132
No. : ARE-046
1. MEASURE CARRIED OUT TO ALLEVIA PROBLEMS OF ELECTRICAL NOISE. TE 2. MEASURE CARRIED OUT TO STABILIZE THE RETURN OF THE PPD1 ACTUA AND TOR MEASURE CARRIED OUT TO ALLEVIA PROBLEMS OF ABNORMAL NOISE WHICH HAD TE BEEN OCCURRING DURING PAPER FEEDING OPERA TIONS. 3. MEASURE CARRIED OUT TO ALLEVIA PROBLEMS OF JAMS IN THE U-TURN PAPER TE GUIDE SECTION.
1. Measure carried out to alleviate problems of electrical noise.
1.Model Name:
AR-5132 (for machines bound for the U.K., Germany, Europe, and Australia markets).
2.General:
The addition of a mesh harness has been carried out to the rear side of the ADU unit. This change has been carried out as a measure to alleviate problems of electrical noise.
ADU unit rear side
Mesh harness
3.Action:
From the 1st lot of 1997 February production. 2. Measure carried out to stabilize the return of the PPD1 actuator and measure carried out to alleviate problems of abnormal noise which had been |
ARE047.PDF | | Date : Aug. 1, 1997
DIGITAL COPIER : AR-5040
No. : ARE-047
1.CHANGES CARRIED OUT IN THE FINISHING UNIT AS A MEASURE TO IMPROVE PRODUCTIVITY . 2.CORRECTION CARRIED OUT IN THE PARTS GUIDE.
1. Changes carried out in the finishing unit as a measure to improve productivity.
1.Model Name:
AR-5040
2.General:
Achange has been carried out in the materials used for some of the parts used in the finisher unit. These changes have been carried out as a measure to improve productivity. Please refer to the parts list for details concerning the parts in which changes were carried out, and their part codes.
3.Action:
From the 1st lot of 1997 July production. 2. Correction carried out in the parts guide.
1.Model Name:
AR-5040
2.General:
Achange has been carried out in some of the screws in certain locations since the 1st lot of mass production. In accordance with this change a correction was necessary in the parts guide and has therefore been carried out.
Two grounding terminals are secured |
ARE048.PDF | | Date : Aug. 22, 1997 DIGITAL COPIER : AR-5132 No. : ARE-048
[Service Information]
CORRECTIONS CARRIED OUT IN THE PARTS GUIDE OF MODELAR5132.
1.Model Name: AR-5132
2.General:
There were some errors discovered in the parts guides for the models listed above. The parts guide errors have been corrected, and are hereby reported.
3.Description:
1 Exteriors
Current parts Version P/G No. Parts code U.S.A. 1 ---Parts code PSHEP4498FCZZ New parts Price rank AC Parts name
FDA Protect sheet
FDA Protect sheet
1/2
Green C
SHARP CORPORATION
Reprography Division
7 Front frame left
Current parts Version P/G No. Parts code 200V series 7 -6 7 -28 7 PFILZ0191FCZZ CFILZ0260FC01 PSHEP3950FCZZ CFILZ0261FC01 AU Ozone filter ER Ozone filter EF Parts code New parts Price rank Parts name
Added ozone filter ER
Ozone filter EF
14 Toner hopper section
Current parts Version P/G No. Parts code All 14 ---Parts code PMLT-1129FCZZ New parts Price rank AC Parts name
Hopper seal B
Added hopper seal B
2/2 |
ARE049.PDF | | Date : Aug. 22, 1997
DIGITAL COPIER : AR-5132
No. : ARE-049
[Service Information]
CHANGE IN AUD INTERF ACE HARNESS WIRING.
1.Model Name:
AR-5132
2.General:
Because the 2P connector harness for the AUD interface harness counter in the control panel unit is too long, it may get caught when the cabinet is being put on during repair. Therefore the changes below have been made to the wiring method.
LCD control PWB
White
AUD interface harness DHAI-2530FCZZ
Red
Wire so it catches on the boss. Door SW
OP PWB
Panel side To OPC PWB
Fastening band
As shown in the diagram above, bend connector C away from fastening band "a", and fasten the harness for connectors B & C 40mm from fastening band a with "a" fastening band.
3.Action:
From the 1st lot of 1997 July production.
1/2
Green C
SHARP CORPORATION
Reprography Division
Current parts Ref. No. Model name Version P/G No. Parts code LBNDJ0013FCZZ (Q'ty: 2)
New parts Parts code Q'ty change: 2 3 Price rank AA Parts name
Effec- In |
ARE050.PDF | | Date : Dec. 1, 1997
DIGITAL COPIER : AR-5132
No. : ARE-050
1.ACHANGE TO THE LOWER SUCTION PLA MA TE TERIAL. 2.ACHANGE TO THE SHAPE OF THE BRAKE SPRING IN THE 500 TRA Y PAPER SUPPLY UNIT.
1. Achange to the lower suction plate material.
1.Model Name:
AR-5132
2.General:
In order to increase productivity, we have changed the material used in the transport DV guide unit's lower suction plate to a recycled material.
3.Action:
From the 1st lot of August, 1997 production on.
1/2
Green C
SHARP CORPORATION
Reprography Division
2. Achange to the shape of the brake spring in the 500 tray paper supply unit.
1.Model Name:
AR-5132
2.General:
In order to improve productivity, we have changed the shape of the brake spring in the 500 tray paper supply unit.
3.Action:
From the middle of August, 1997 production (running change).
Current parts Ref. No. Model name Version P/G No. Parts code
New parts Parts code Price rank AL Parts name
Effec- Intertive changeability time 1st lot '97/8 1 |
ARE051.PDF | | Date : Sep. 12, 1997
DIGITAL COPIER : AR-5132
No. : ARE-051
ABOUT ESTABLISHING REGIMYLAR AS ASERVICE PART.
1.Model Name:
AR-5132
2.General:
We have established the regimylar attached to the desk's paper guide E as a service part.
Regimylar 0CW4067P030//
* Regimylar was added to all the mass-produced units from the first one on, and has now been established as a service part.
Current parts Ref. No. Model name Version P/G No. Parts code All 42 ---Parts code 0CW4067P030// New parts Price rank AP Parts name Effec- Intertive changetime ability -------
Note
AR-5132
Regimylar
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 4. Not interchangeable. 5. Interchangeable if replaced with same types of related parts in use. 6. Others.
Parts marked with `` '' is important for maintaining the safety of the |
ARE052.PDF | | Date : Oct. 1, 1997
DIGITAL COPIER : AR-5132
No. : ARE-052
CHANGE IN THE IC (SRAM) CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY.
1.Model Name:
AR-5132
2.General:
The IC(SRAM) used in the ICU PWB has been changed to improve productivity.
3.Action:
From the start of 1997 August production.
Current parts Ref. No. Model name Version P/G No. Parts code
New parts Parts code Price rank AY Parts name
Effec- Intertive changeability time 1st lot '97/8
Note
AR-5132
All
51 -60
VHI7C185-25VC
VHIH256-20-8A
IC [IC725,744]
1
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 4. Not interchangeable. 5. Interchangeable if replaced with same types of related parts in use. 6. Others.
Parts marked with `` '' is important for maintaining the safety of the set. Be sure to replace these parts with specifi |
ARE053.PDF | | Date : Oct. 2, 1997
DIGITAL COPIER : AR-5040
No. : ARE-053
[Service Information]
MEASURE TO ESTABLISH COMPLIANCE WITH THE CE STANDARDS FOR THE DC POWER SUPPLY PWB.
1.Model Name:
AR-5040 (only for machines bound for the 200 V market destinations.)
2.General:
The addition of a harness has been carried out on the DC power supply PWB. The addition of the harness has been carried out as a measure to comply with the CE standards (noise standards). The harness connects with the parts on the machines side which comply with CE standards, but the parts in the machine which comply with the CE standards are a little late, and the harness cannot be used during this period. (Due to the ordering status of the DC power supply PWB, the measures carried out on the machine itself will have been carried out first.)
The old PWB and the new PWB are interchangeable until the CE compliance measures have been carried out on the machine.
Harness in compliance with the CE standards
New parts Parts code P |
ARE055.PDF | | Date Dec. 5, 1997 Digital copier AR-5132 No. ARE-055
[Service Information]
Change of parts in the optical unit (productivity improvement)
1.Model Name: AR-5132
2.General
Productivity is improved by changing the material, surface treatment method and so on for some parts in the optical unit.
3.Description:
Change of shape of OC fixing plate
4.Action
From the middle of production of July, 1997 (floating switch on the way of production)
Ref. No.
Model name
Current parts Version P/G No. Parts code All 4 -79 LPLTM4997FCZ1
New parts Parts code LPLTM4997FCZ2 Price rank AP Parts name OC FIXING PLATE S
Effec- Intertive change- Note ability time Mid'97/7 1
AR-5132
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 4. Not interchangeable. 5. Interchangeable if replaced with same types of related parts |
ARE056.PDF | | Date : Oct. 23, 1997
DIGITAL COPIER : AR-5132
No. : ARE-056
[Service Information]
CORRECTION CARRIED OUT IN THE PARTS GUIDE FOR MODELAR-5132.
AR-5132
1.Model Name:
2.General:
There was a mistake that was found in the parts guide for model AR-5132. The mistake has been corrected.
3.Description:
The parts for [52] PCU PWB listed below were mistakenly left out of the parts guide for model AR-5132, and have therefore been added.
Current parts Ref. No. Model name Version P/G No. Parts code
New parts Parts code Price rank BE Parts name
Effec- Intertive changeability time
Note
AR-5132
All
52
----
VHIHD8-570L04
IC (HD8-570L04) 1st lot [IC 106]
6
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 4. Not interchangeable. 5. Interchangeable if replaced with same types of related parts in use. 6. O |
ARE057.PDF | | Date : Oct. 24, 1997
DIGITAL COPIER : AR-5040
No. : ARE-057
REGARDING CHANGES TO THE DEVELOPER UNIT'S INTERNAL DV COVER U.
1.Model Name:
AR-5040
2.General:
In order to increase part interchangeability between different models, we have changed the shape of the developer unit's internal DV cover u.
Changed thickness from 3.0 mm to 2.5 mm.
3.Action:
From the first unit of September, 1997 production on.
Current parts Ref. No. Model name Version P/G No. Parts code Parts code New parts Price rank AL Parts name Effec- Intertive changetime ability 1st lot '97/9
Note
AR-5040
All
17 -71
PCOVP0799FCZZ
PCOVP0799FCZ1
DV cover U
1
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 4. Not interchangeable. 5. Interchangeable if replaced with same types of related parts in use. 6. Others.
Parts marked |
ARE058.PDF | | Date : Oct. 30, 1997
DIGITAL COPIER : AR-5132
No. : ARE-058
1.PREVENTING PAPER JAMS A THE DESK'S 500 SHEET CASSETTE. T 2.ACHANGE TO THE OPERA TION CONTROL PWB (FOR IMPROVED PRODUCTIVITY).
1. Preventing paper jams at the desk's 500 sheet cassette.
1.Model Name:
AR-5132
2.General:
In order to prevent jams that may occur when the desk's 500 cassette is using A4 or letter size paper, we have made the following changes.
3.Description:
We have changed the desk control PWB's ROM software so that the PWB does not check for TRC signals within 300 msec of the paper supply signal, since mistaken TRC signal detection is the cause of many paper jams. (Changing the ROM on an old PWB makes it equivalent to a new PWB.) Furthermore, we have established a new PWB for Europe in order to comply with CE mark regulations.
4.Action:
From the first unit of September, 1997 production on. 2. Achange to the operation control PWB (For improved productivity).
1.Model Name:
AR-5132
2.General:
In order |
ARE059.PDF | | Date : Nov. 20, 1997
DIGITAL COPIER : AR-5132
No. : ARE-059
[Service Information]
REGARDING REVISIONS TO THE PARTS GUIDE FOR AR-5132.
1.Model Name:
AR-5132
2.General:
We have revised mistakes in the parts guide for the above model.
3.Description:
38 RADF: Paper feeding transport section 2
Current parts P/G No. Parts code 38 -68 0CW2214P102// Parts code 0CW2223P102// New parts Price rank AH Parts name
Plate 1
1/3
Green C
SHARP CORPORATION
Reprography Division
2/3
3/3
|
ARE060.PDF | | Date : Feb. 9, 1998
DIGITAL COPIER : AR-5132
No. : ARE-060
[Service Information]
ESTABLISHMENT OF THE TONER TRANSPORT PIPE A TTACHMENT ARRON ALPHA801 F AS ASERVICE PART.
1.Model Name:
AR-5132
2.General:
The toner transport pipe attachment Arron alpha 801 F of the DV unit section has been established as a service part.
3.Description:
The Arron alpha 801F (20g/unit) has been established as a service part. The part code for the Arron alpha 801F is UKOG-0256FCZZ.
Arron alpha 801F Two droplets in the semi-portal direction (approx. 0.5g)
With a limit
Area of application after adhesion operations have been completed (the bottom surface of the U-groove)
Adhesion standard
Toner transport pipe
The engraved lettering should face upward
Toner transport pipe
Toner transport pipe attachment diagram
1/2
Green C
SHARP CORPORATION
Reprography Division
Current parts Ref. No. Model name Version P/G No. Parts code All -------
New parts Parts code UKOG-0256FCZZ Price rank BH Parts nam |
ARE061.PDF | | Date : Dec. 19, 1997
DIGITAL COPIER : AR-5130/5040
No. : ARE-061
1.CHANGE CARRIED OUT IN THE CG-ROM IN THE OPERA TIONS CONTROL PWB TO A MASK ROM. 2.CHANGE CARRIED OUT IN THE PAPER DELIVERY SCREW PARTS.
1. Change carried out in the CG-ROM in the operations control PWB to a mask ROM.
1.Model Name:
AR-5130
2.General:
Achange has been carried out in the CG-ROM (IC 305) in the operations control PWB. The ROM has been changed to a mask ROM. This action has been carried out as a measure to improve productivity.
[Old] VHITC532000AF
[New] VHILH532K7K-1
For identification, LH532K7K is silk-screen printed on the CG-ROM.
3.Action:
From the 1st lot of 1997 October production.
2. Change carried out in the paper delivery screw parts.
1.Model Name:
AR-5040
2.General:
The paper delivery screw Awhich was used in the toner box unit and the DR cleaner unit has been discontinued. In its place, the C16 toner screw HI/E unit is now being used. This action has been carried out as a measure to |
ARE062.PDF | | Date : Dec. 26, 1997
DIGITAL COPIER : AR-5132
No. : ARE-062
1. CHANGE CARRIED OUT IN THE METHOD OF A TTACHMENT OF THE OC A TTACHMENT PLA TE. 2. MEASURE TO ALLEVIA PROBLEMS OF BLURRING OF THE COPY TE IMAGES.
1. Change carried out in the method of attachment of the OC attachment plate.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the fixing screws and the fixing screw retainer positions. This action has been carried out as a measure to secure and stabilize the OC attachment plate in the optical unit.
Screw retainer (XHBSE40P10000)
OC Attachment plate (The change described above has been carried out in the same way to the OC attachment plate on the left side of the machine.)
3.Action:
From 1997 mid-October production.
1/2
Green C
SHARP CORPORATION
Reprography Division
2. Measure to alleviate problems of blurring of the copy images.
1.Model Name:
AR-5132 (Only for machines of the 200V series)
2.General:
There was a possibility of copy image blurring occ |
ARE063.PDF | | Date : Dec. 26, 1997
DIGITAL COPIER : AR-5132
No. : ARE-063
CHANGE CARRIED OUT IN THE SHAPE OF CENTER TRA Y.
1.Model Name:
AR-5132
2.General:
There have been problems of paper jams occurring when paper feeding operations are carried out from the ADU due to the copy paper getting caught on some of the holes between the paper feeding ribs. As a measure to alleviate this problem, a change has been carried out in the metal mold, and the holes have been filled in. In addition to this action, the addition of a harness retainer sheet has been carried out. Furthermore, at the same time, the addition of a notch has been carried out to the interfering section of the center tray. This action has been carried out as a measure to prevent contact between the center tray and the machine rear frame PWB supporter.
The addition of a notch has been carried out to the section of the center tray which interferes when loading the tray into the machine.
The holes (Qty: 7) have been filled in, and at |
ARE064.PDF | | Date : Jan. 9, 1998
DIGITAL COPIER : AR-5132
No. : ARE-064
CHANGE CARRIED OUT IN THE SHAPE OF HANDLE OF THE PAPER FEED COVER.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the shape of the handle of the paper feed cover. This action has been carried out as a measure to improve operationability. In accordance with this change, a change has also been carried out in the color of the resist guide. Black has been changed to OAgray.
·
Cross section of the paper feed cover
(Old) 0CW2214P008C/
(New) 0CW2214P008D/
3.Action:
From the 1st lot of 1997 October production.
1/2
Green C
SHARP CORPORATION
Reprography Division
Current parts Ref. No. Model name Version P/G No. Parts code 38 -20 AR-5132 All 38 -21 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 0CW2214P008C/ 0CW2214P034// |
ARE065.PDF | | Date : Dec. 26, 1997
DIGITAL COPIER : AR-5132
No. : ARE-065
[Service Information]
CORRECTIONS CARRIED OUT IN THE PARTS GUIDE OF MODELAR-5132.
1.Model Name:
AR-5132
2.General:
There was an error in the parts guide of the model listed above, and has been corrected.
3.Description:
Current parts Version P/G No. Parts code 200V series 1 ---Parts code PCUSS0001GCZZ New parts Price rank AE Parts name
Gasket
Added Gasket
1/2
Green C
SHARP CORPORATION
Reprography Division
4
Optical section
Current parts New parts Parts code PGSK-1002LCZZ Price rank AC Parts name P/G No. Parts code
Version
200V series
4 -
----
Gasket
Added Gasket
12 Optical frame 2
Current parts Version P/G No. Parts code Parts code PGSK-0016FCZZ 200V series 12 ---PGSK-0015FCZZ AN New parts Price rank AG Gasket Parts name
Added Gasket PGSK-0016FCZZ Added Gasket PGSK-0015FCZZ
10 Rear frame 2
Current parts Version P/G No. Parts code 200V series 10 -27 DHAI-2776FCZZ Parts code DHAI-2776FC11 New parts Price r |
ARE066.PDF | | Date : Jan. 9, 1998
DIGITAL COPIER : AR-5132
No. : ARE-066
MEASURE TO ESTABLISH INTERCHANGEABILITY OF PARTS IN THE PAPER FEED TRA UNIT. Y
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the original tray and the tray sensor lever. This action has been carried out as a measure to establish interchangeability of parts with other models.
Change items that were carried out in the original tray unit. [Old] [New]
Added hole
Change items that were carried out in the tray sensor lever.
[Old]
[New]
3.Action:
From 1997 mid-October production.
1/2
Green C
SHARP CORPORATION
Reprography Division
Current parts Ref. No. Model name Version P/G No. Parts code 35 -11 AR-5132 All 35 -19 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 0CW2199P017// 0CW2214P017//
New parts Parts code 0CW22 |
ARE067.PDF | | Date : Jan. 9, 1998
DIGITAL COPIER : AR-5132
No. : ARE-067
[Service Information]
CORRECTIONS CARRIED OUT IN THE PARTS GUIDE OF MODELAR-5132.
1.Model Name:
AR-5132
2.General:
There were some errors found in the parts guide of the model listed above. The errors have been corrected, and are hereby reported.
3.Description:
There were some errors found in the part codes and part names in the parts guide list [42]-8 and [43]-4 (please refer to the lists shown below). These errors have been corrected.
``2" has been corrected to ''1".
``1" has been corrected to ''2".
SHARP CORPORATION
Reprography Division
Green C
|
ARE068.PDF | | Date : Jan. 19, 1998
DIGITAL COPIER : AR-5040
No. : ARE-068
1. CHANGE CARRIED OUT IN THE PRINTED CONTENT OF THE MSDS CARD. 2. MEASURE TO PREVENT CHAFFING OF THE COPY PAPER. 3. MEASURE TO ALLEVIA PROBLEMS OF ABNORMAL NOISE FROM TE THE COPY PAPER FEED DRIVE UNIT.
1. Change carried out in the printed content of the MSDS card.
1.Model Name:
AR-5040 (only for machines bound for the U.S.A., U.K. Canada markets).
2.General:
There was a change that was carried out in the type of material used for the carbon block used for the toner. In accordance with this change a change has also been carried out in the written content of the MSDS card.
3.Action:
From 1996 October production. 2. Measure to prevent chaffing of the copy paper.
1.Model Name:
AR-5040
2.General:
There have been problems of the edges of the copy paper chaffing against the paper guide of the delivery guide section of the finisher. As a measure to alleviate this trouble, a change has been carried out in the curved positio |
ARE069.PDF | | Date : Jan. 19, 1998
DIGITAL COPIER : AR-5040
No. : ARE-069
[Service Information]
CHANGE IN THE MAKER CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY .
1.Model Name:
AR-5040
2.General:
Achange has been carried out in the maker of some of the parts. This action has been carried out as a measure to improve productivity. In accordance with this change a change has also been carried out in the part codes.
3.Action:
From the 1st lot of 1996 June production.
Current parts Ref. No. Model name Version P/G No. Parts code 68 -48 AR-5040 All 35 -6 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. DUNT-6718FCZZ VHI422000A32F
New parts Parts code VHI23232C60BS DUNT-6718FC11 Price rank CH CL Parts name
Effec- Intertive changeability time
Note
IC [IC 1, 2] HDD unit
1st lot '96/9
1
4. Not interchangeabl |
ARE071.PDF | | Date : Jan. 19, 1998
DIGITAL COPIER : AR-5132
No. : ARE-071
CHANGE IN THE A TTACHMENT SCREWS OF THE F AN A TTACHMENT PLA CARRIED OUT AS A MEASURE TO TE IMPROVE PRODUCTIVITY.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the attachment screws of the fan attachment plate. This action has been carried out as a measure to improve productivity. The attachment screws have been changed from M4 × 10 screws to M4 × 6 screws.
Fan attachment plate
Changed screw (M4 × 10 M4 × 6)
Changed screw (M4 × 10 M4 × 6)
3.Action:
From 1997 mid-November production.
Current parts Ref. No. Model name Version P/G No. Parts code Parts code New parts Price rank AA Parts name Effec- Intertive changetime ability Mid'97/11
Note
AR-5132
All
7 -18
XHBSE40P10000
LX-BZ0502FCZZ
Screw (M4 × 10)
1
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. Ne |
ARE072.PDF | | Date : Jan. 19, 1998
DIGITAL COPIER : AR-5132
No. : ARE-072
MEASURE TO ALLEVIA PROBLEMS OF FUSING JAMS TE DURING DOUBLE SIDE COPY OPERA TIONS.
1.Model Name:
AR-5132
2.General:
There have been problems of jams occurring during double side copy operations using A3 size copy paper in the 200 V series markets. As a measure to alleviate this trouble, the attachment of a duct sheet has been carried out in the ducts of the main body of the machines. In addition, ribs have been designed to attach the duct sheets in the ducts. It is important to note that in the case of machines in the 100 V series markets, the ducts of the main body of the machines in which the ribs have been added are in fact being used, but the duct sheets have not been attached.
The main body duct
The main body duct sheet
3.Action:
Ref. No. Model name
AR-5132 (200 V series): AR-5132 (100 V series):
From the 1st lot of 1997 September production. Running change from 1997 September production.
New parts Parts code |
ARE073.PDF | | Date : Jan. 19, 1998
DIGITAL COPIER : AR-5132
No. : ARE-073
1. MEASURE TO STABILIZE THE RETURN OF THE PPD1 ACTUA TOR. 2. MEASURE TO ALLEVIA PROBLEMS OF DIAGONAL FEEDING OF THE ORIGINAL TE DOCUMENTS IN THE ADF . 3. CHANGE IN THE A TTACHMENT SCREWS OF THE F A AN TTACHMENT BASE PLA TE CARRIED OUT AS AMEASURE TO IMPROVE OPERA TIONABILITY. 4. CHANGE IN THE PART CODE CARRIED OUT IN ACCORDANCE WITH ACHANGE IN THE MAKER (ACTION CARRIED OUT AS AMEASURE TO IMPROVE PRODUCTIVITY).
1. Measure to stabilize the return of the PPD1 actuator.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the load of the pawl spring. This action has been carried out as a measure to stabilize the return of the PPD1 actuator in the transport DV guide unit.
3.Action:
Running change from 1997 September production.
2. Measure to alleviate problems of diagonal feeding of the original documents in the ADF .
1.Model Name:
AR-5132
2.General:
There have been problems of diagonal feeding of original d |
ARE074.PDF | | Date : Jan. 19, 1998
DIGITAL COPIER : AR-5132
No. : ARE-074
[Service Information]
CORRECTIONS CARRIED OUT IN THE PARTS GUIDE.
1.Model Name:
AR-5132
2.General:
There were some errors found in the parts guide of the model listed above. The errors have been corrected, and are hereby reported.
3.Description:
[1] Achange has been carried out in the shape of illustration No. 15 of the outer case and its attachment position as described in the figure shown below.
Eliminated
Added
SHARP CORPORATION
Reprography Division
Green C
|
ARE075.PDF | | Date : Jan. 26, 1998
DIGITAL COPIER : AR-5132
No. : ARE-075
1.CHANGE CARRIED OUT IN THE PART CODE FOR THE LASER SCANNER UNIT. 2.CHANGE CARRIED OUT IN THE MA TERIALS USED IN THE TRANSFORMER FIXING PLA TE.
1. Change carried out in the part code for the laser scanner unit.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the maker of the parts for the laser scanner unit. This action has been carried out as a measure to improve productivity. In accordance with this change a change has also been carried out in the part code.
Laser scanner PC
DUNT-6747FC12
DUNT-6747FC13
3.Action:
Running change from 1998 mid-April production.
1/2
Green C
SHARP CORPORATION
Reprography Division
2. Change carried out in the materials used in the transformer fixing plate.
1.Model Name:
AR-5132 (200 V series)
2.General:
Achange has been carried out in the material used for the transformer fixing plate. This action has been carried out as a measure to improve product |
ARE076.PDF | | Date : Jan. 26, 1998
DIGITAL COPIER : AR-5132/5040
No. : ARE-076
MEASURE TO ESTABLISH PARTS INTERCHANGEABILITY OF THE LIFT PLA TE.
1.Model Name:
AR-5132/5040
2.General:
Achange has been carried out in the lift plate. This action has been carried out as a measure to establish parts interchangeability with other models.
3.Action:
From the start of 1997 November production.
Current parts Ref. No. Model name Version P/G No. Parts code 30 -18 AR-5132 All AR-5040 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 48 -29 44 -29 LPLTM4043FCZZ
New parts Parts code Price rank Parts name
Effec- Intertive changeability time
Note
LPLTM4043FCZ1
AG
Lift plate
1st lot '97/11
1
4. Not interchangeable. 5. Interchangeable if replaced with same types of related parts in use. 6. Others.
Parts marked with `` |
ARE077.PDF | | Date : Feb. 27, 1998
DIGITAL COPIER : AR-5132 etc.
No. : ARE-077
1.CHANGE CARRIED OUT IN THE PARTS USED IN THE TRA DRA Y WER UNIT. 2.CHANGECARRIED OUT IN THE PARTSUSEDINTHETRAASSEMBLYDRA Y WERUNIT . 3.CHANGE CARRIED OUT IN THE PARTS USED IN THE ADU UNIT.
1. Change carried out in the parts used in the tray drawer unit.
1.Model Name:
AR-5132/5040
2.General:
The bit insert of the tray handle attachment section has been discontinued, and the part is now attached by a binding screw fixing method. This action has been carried out as a measure to improve productivity.
3.Interchangeability:
Old parts are interchangeable only with old parts, and new parts are interchangeable only with new parts. Drawer case Tray handle Screw GCASP0155FCZZ JHNDP0107FCZZ XBTSE40P08000 GCASP0155FCZ1 JHNDP0107FCZ1 XEBSE40P10000
4.Action:
From 1997 mid-December production. 1/4
Green C
SHARP CORPORATION
Reprography Division
2. Change carried out in the parts used in the tray ass |
ARE078.PDF | | Date : Feb. 27, 1998
DIGITAL COPIER : AR-5132
No. : ARE-078
CHANGE CARRIED OUT IN GEAR 28T INSIDE THE TONER HOPPER UNIT.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the maker of the gear 28T used inside the toner hopper unit. This action has been carried out as a measure to improve productivity. In accordance with this change a change has also been carried out in the part code, as shown below.
Gear 28T
NGERH0349FCZZ
NGERH1284FCZZ
3.Action:
From the 1st lot of 1998 January production.
Current parts Ref. No. Model name Version P/G No. Parts code
New parts Parts code Price rank AD Parts name
Effec- Intertive changeability time 1st lot '98/1
Note
AR-5132
All
14 -31
NGERH0349FCZZ
NGERH1284FCZZ
Gear 28T
1
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of cu |
ARE079.PDF | | Date : Mar. 2, 1998
DIGITAL COPIER : AR-5132
No. : ARE-079
CHANGE CARRIED OUT IN THE IC OF THE ICU PWB.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the IC of the ICU PWB. This action has been carried out as a measure to improve the reliability of the part.
IC817
VHI74VHC244/1
VHI74AC244/-1
3.Action:
Running change from 1998 January production.
Current parts Ref. No. Model name Version P/G No. Parts code All 51 -64 VHI74VHC244/1
New parts Parts code VHI74AC244/-1 Price rank AK IC Parts name
Effec- Intertive changeability time
Note
AR-5132
1
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 4. Not interchangeable. 5. Interchangeable if replaced with same types of related parts in use. 6. Others.
Parts marked with `` '' is importan |
ARE080.PDF | | Date : Mar. 24, 1998
DIGITAL COPIER : AR-5132/5040
No. : ARE-080
CHANGE IN THE 500 TRA COPY PAPER FEEDING UNIT CARRIED OUT Y AS AMEASURE TO ESTABLISH INTERCHANGEABILITY OF PARTS BETWEEN MODELS.
1.Model Name:
AR-5132/5040
2.General:
The change in the 500 tray copy paper feeding unit described below has been carried out as a measure to establish interchangeability of parts between models.
(Old) DUNT-6546FC13
(New) DUNT-6923FCZZ
Please refer to the following pages for details concerning the composition parts of the new unit.
3. Interchangeability:
Parts (unit assemblies) are interchangeable between old and new units. [It is important to note that unit assembly parts (individual parts) are not interchangeable, and it is therefore necessary to exercise caution when carrying out replacement operations.]
4.Action:
From the start of 1998 February production.
1/4
Green C
SHARP CORPORATION
Reprography Division
500 paper feeding unit
2/4
Current parts Ref. No. Model name V |
ARE082.PDF | | Date : May. 15, 1998
DIGITAL COPIER : AR-5132
No. : ARE-082
CHANGES CARRIED OUT IN SOME OF THE PARTS IN THE ADU UNIT .
1.Model Name:
AR-5132
2.General:
Changes have been carried out in the makers of the parts listed below. This action has been carried out as a measure to improve productivity. In accordance with these changes, changes has also been carried out in the part codes.
3.Action:
From the start of 1998 March production.
Current parts Ref. No. Model name Version P/G No. Parts code 33 -21 33 -28 AR-5132 All 33 -29 33 -22 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. NGERR0614FCZZ NBRGC0344FCZZ NGERH0612FCZZ NGERH0613FCZZ
New parts Parts code NGERH1229FCZZ NGERH1228FCZZ NGERR1230FCZZ AF NBRGY1032HCZZ Bearing Price rank AE AD Parts name
Effec- Intertive changeability time
Note
Drive g |
ARE083.PDF | | Date : May. 21, 1998
DIGITAL COPIER : AR-5132
No. : ARE-083
[Service Information]
CORRECTIONS CARRIED OUT TO THE PARTS GUIDE OF MODEL AR-5132.
1.Model Name:
AR-5132
2.General:
There was an error discovered in the parts guides of the model listed above. The error has been corrected and is hereby reported.
3.Description:
The part code of the pick up roller of the desk LCC paper feeding unit was not correct and has therefore been corrected.
[Parts Location Diagram]
Pick up roller
Desk LCC paper feeding unit
Current parts Version P/G No. Parts code Overseas 43 -12 0CW4051P320//
New parts Parts code 0CW4051P397// Price rank AS Parts name
Effec- Intertive changetime ability 1st lot 3
Note
Pick up roller
SHARP CORPORATION
Reprography Division
Green C
|
ARE084.PDF | | Date : Jun. 2, 1998
DIGITAL COPIER : AR-5132
No. : ARE-084
1. CHANGE CARRIED OUT IN THE ADJUSTMENT RANGE OF THE (LCD) BRIGHTNESS CONTROL FUNCTION OF THE MESSAGE DISPLAY. 2. CHANGE CARRIED OUT IN THE GROUNDING TERMI NAL OF THE AC CORD SECTION.
1. Change carried out in the adjustment range of the (LCD) brightness control function of the message display.
1.Model Name:
AR-5132
2.General:
The adjustment range of the darken control of the (LCD) brightness control functions of the message display was too narrow, and as a measure to alleviate the problem the change described below was carried out in the resistance in the operations control PWB. As a result of the change, the general, overall adjustment range was shifted to a darker level. Resistor VRS-TS2AD332J VRS-TS2AD222J
3.Action:
From the start of 1998 April production.
2. Change carried out in the grounding terminal of the AC cord section.
1.Model Name:
AR-5132 (only for machines bound for the U. S. A. |
ARE085.PDF | | Date : Jun. 22, 1998
DIGITAL COPIER : AR-5132
No. : ARE-085
1. MEASURE TO ALLEVIA PROBLEMS OF THE TONER LEAKING FROM THE TE TONER HOPPER. 2. CHANGE CARRIED OUT IN THE COPY PAPER CASSETTE IN MACHINES BOUND FOR THE CHINESE MARKET. 3. MEASURE TO ALLEVIA PROBLEMS OF CURLING DURING PAPER FEEDING TE OPERA TIONS IN THE ADU UNIT.
1. Measure to alleviate problems of the toner leaking from the toner hopper.
1.Model Name:
AR-5132
2.General:
There have been problems of the toner leaking from the mixing shaft section during toner feeding operations. As a measure to alleviate this problem, the addition of a cover sheet has been carried out.
Attachment standard
Attachment standard
Attachment standard
Hopper cover sheet R Note: <1> All attachment surfaces should be wiped with alcohol. (In particular, care should be exercised to wipe the bottom surfaces of the ribs.) <2> Remove the sheet attached on the two-sided tape, bend surface (B) of the sheet along the bending standard (A) and attach. < |
ARE086.PDF | | Date : Jun. 8, 1998
DIGITAL COPIER : AR-5132
No. : ARE-086
[Service Information]
CORRECTIONS CARRIED OUT IN THE PARTS GUIDE OF MODEL AR-5132.
1.Model Name:
AR-5132
2.General:
There were some errors found in the parts guide of the model listed above. The errors have been corrected and are hereby reported.
3.Description:
There was an error found in the parts guide of the model listed above. The part code for Block [42] - No. 9 Gear was incorrect and has been corrected as shown below.
[42] Desk: Paper feeding jam cover section.
Current parts P/G No. Parts code Parts code New parts Price rank AE Parts name
42 -9
0CW4067P010//
0CW4051P034//
Gear (GER-0.8-20)
SHARP CORPORATION
Reprography Division
Green C
|
ARE088.PDF | | Date : Jun. 29, 1998
DIGITAL COPIER : AR-5132
No. : ARE-088
1. ACTION TO PREVENT CONTACT BETWEEN THE COVER OF THE DARK BOX AND THE COPY LAMP UNIT. 2. DISCONTINUANCE OF THE SCREW HOLE TAPPING IN THE F A AN TTACHMENT PLA CARRIED OUT AS AMEASURE TO IMPROVE PRODUCTIVITY. TE,
1. Action to prevent contact between the cover of the dark box and the copy lamp unit.
1.Model Name:
AR-5132 (only for machines bound for the 200 V series market destinations).
2.General:
There have been problems reported of contact between the CCD unit and the dark box cover during scanning operations of the copy lamp. As a measure to alleviate this problem, a change has been carried out in the dimensions of the gasket which is attached in the gap between the CCD unit and the dark box cover, and a change in the cover of the dark box has been carried to so that it does not rise up.
Attachment should be carried out in approximately the center. Gasket PGSK-0020FCZZ Attachment standard
Gasket (l = 100 mm) CCD unit |
ARE089.PDF | | Date: Jun. 24, 1998
DISITAL COPIER: AR-5040
No. : ARE-089
1. Use of recycled material
1. Use of recycled material
1. Model Name:
AR-5040 As the environmental countermeasure, some resin parts of the above models are changed to those which use the recycled materials. For the relevant parts and part codes, also refer to the parts list. From the middle of the production in May, 1998 (Running change)
2. General:
3. Action:
Current parts Ref. No. Model name Version P/G No. Parts code PGIDM1445FCZZ LDAIU0466FCZZ
New parts Parts code PGIDM1445FCZ1 LDAIU0466FC10 Price rank AP Parts name
Effec- Intertive change- Note time ability
16 - 8 16 - 1 1 AR-5040 ALL 16 - 2
Cartridg guide Shutter Base A Upper
LDAIU0466FCZ1
LDAIU0466FC11
AH
Shutter Base B Upper C Shutter Base Lower
Mid'98/5
1
16 - 4 1. Interchangeable.
LDAIU0467FCZZ
LDAIU0467FCZ2
4. Not interchangeable. 5. Interchangeable if replaced with same types of related parts in use. 6. Others.
2. Current type can |
ARE090.PDF | | Date : Jul. 2, 1998
DIGITAL COPIER : AR-5132
No. : ARE-090
[Service Information]
CORRECTIONS CARRIED OUT IN THE PARTS GUIDE OF MODELAR-5132.
1.Model Name:
AR-5132
2.General:
There was an error found in the parts guide of the model listed above. The error has been corrected and is hereby reported.
3.Description:
14 Toner Hopper Section.
Current parts Version P/G No. Parts code Overseas 14 ---Parts code PPIPP0194FCZZ New parts Price rank AH Parts name
Toner transport pipe
Added toner transport pipe
SHARP CORPORATION
Reprography Division
Green C
|
ARE091.PDF | | Date : Jul. 10, 1998
DIGITAL COPIER : AR-5132
No. : ARE-091
1. CHANGE IN THE SCREWS IN THE OPTICAL UNIT CARRIED OUT AS AMEASURE TO IMPROVE PRODUCTIVITY. 2. MEASURE TO ALLEVIATE PROBLEMS OF OIL OOZING FROM THE BUSHING IN THE DEVELOPING UNIT . 3. ADDITION CARRIED OUT OF AN ICU COVER SHEET. 4. MEASURE TO IMPROVE OPERATION STABILITY OF THE SHUTTER IN THE TONER BOX. 5. CHANGE CARRIED OUT IN THE MAKER CARRIED OUT AS AMEASURE TO IMPROVE PRODUCTIVITY.
1. Change in the screws in the optical unit carried out as a measure to improve productivity.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in a portion of the screws used in the optical unit (in the locations marked with a "O" in the figure shown below). This action has been carried out as a measure to improve productivity.
3.Action:
From the start of 1998 June production.
2. Measure to alleviate problems of oil oozing from the bushing in the developing unit.
1.Model Name:
AR-5132
2.General:
There have been problems o |
ARE092.PDF | | Date : Jul. 10, 1998
DIGITAL COPIER : AR-5132
No. : ARE-092
1. CHANGE IN THE MATERIAL USED FOR THE ATTACHMENT PLATE OF THE GUIDE SWITCH IN THE TRANSPORT UNIT CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY . 2. CHANGE IN THE MATERIAL OF THE LOWER GUIDE OF THE 500 TRAY PAPER FEEDING UNIT CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY . 3. CHANGE IN THE SHAPE OF THE ADU OF THE ROLLER ARM CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY .
1. Change in the material used for the attachment plate of the guide switch in the transport unit carried out as a measure to improve productivity.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the material used for the attachment plate of the guide switch in the transport unit. This action has been carried out as a measure to improve productivity. In addition to this change the tapping of the attachment holes for the guide switch has been discontinued and the screws have also been changed.
Guide switch attachment plate
Chang |
ARE094.PDF | | Date : Jul. 22, 1998
DIGITAL COPIER : AR-5132
No. : ARE-094
MEASURE TO PREVENT PROBLEMS OF LOOSENING OF THE ATTACHMENT SCREWS OF THE CLUTCH.
1.Model Name:
AR-5132
2.General:
Achange has been carried out in the shape of the attachment screws of the electromagnetic clutch used in the ADU unit. The shape of the tip of the screws has been changed from a half point type to a double point type.
Screw
3.Action:
Running change from 1998 mid-May production.
Current parts Ref. No. Model name Version P/G No. Parts code All 33 -106 PCLC-0207FCZZ
New parts Parts code PCLC-0207FCZ1 Price rank AX Parts name
Effec- Intertive changeability time
Note
AR-5132
CW electromagnetic clutch
1
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 4. Not interchangeable. 5. Interchangeable if replaced with same typ |
ARE098.PDF | | Date : Jul. 31, 1998
DIGITAL COPIER : AR-5132
No. : ARE-098
1. DISCONTINUANCE OF THE SHIELD SEAL IN THE OPTICAL UNIT CARRIED OUT AS AMEASURE TO IMPROVE PRODUCTIVITY. 2. CHANGE CARRIED OUT IN THE EFFECTIVE TIME REPORTED IN T/R ARE-088.
1. Discontinuance of the shield seal in the optical unit carried out as a measure to improve productivity.
1.Model Name:
AR-5132
2.General:
The shield seal in the optical unit has been discontinued. Also the 16 holes in two locations of the optical vibration protect sheet (PSHEG3833FCZZ) have been discontinued. This action has been carried out as a measure to improve productivity. The old optical vibration protect sheet is interchangeable with the new optical vibration protect sheet, and therefore there has been no change carried out in the part code.
3.Action:
From the start of 1998 July production. 2. Change carried out in the effective time reported in T/R ARE-088.
1.Model Name:
AR-5132 (only in machines bound for the 200 V series market des |
ARE099.PDF | | Date : Aug. 5, 1998
DIGITAL COPIER : AR-5040
No. : ARE-099
CHANGE IN THE MAKER OF THE PAPER FEEDING HARNESS CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY.
1.Model Name:
AR-5040
2.General:
Achange in the maker of the harness used in the paper feeding section has been carried out. This action has been carried out as a measure to improve productivity. In accordance with the change described above a change has also been carried out in the part code.
3.Action:
From the start of 1998 July production.
Current parts Ref. No. Model name Version P/G No. Parts code
New parts Parts code Price rank AQ Parts name
Effec- Intertive changeability time 1st lot '98/7
Note
AR-5040
All
21 -23
DHAI-2049FCZZ
DHAI-2049FC11
Paper feeding harness
1
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 4. Not inte |
ARE106.PDF | | Date : Sep. 16, 1998
DIGITAL COPIER : AR-5132
No. : ARE-106
CHANGE IN THE SHAPE OF THE MB DRIVE SHAFT CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY.
1.Model Name:
AR-5132
2.General:
A change has been carried out in the shape of the MB drive shaft used in the optical unit. This action has been carried out as a measure to improve productivity. The change described above has been carried out as illustrated in the diagram shown below.
The unused milling of the F side has been discontinued, and shortened to the E-ring section.
E-ring
Optical base plate
3.Action:
From the 1st lot of 1998 August production.
Current parts Ref. No. Model name Version P/G No. Parts code
New parts Parts code Price rank AT Parts name
Effec- Intertive changetime ability 1st lot '98/8
Note
AR-5132
All
4 -13
NSFTZ2207FCZZ
NSFTZ2207FCZ1
MB drive shaft
1
1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Curre |
ARE107.PDF | | Date : Sep. 18, 1998
DIGITAL COPIER : AR-5132
No. : ARE-107
CHANGE IN THE TRAY INSTRUCTION LABEL CARRIED OUT AS A MEASURE TO IMPROVE PRODUCTIVITY.
1.Model Name:
AR-5132/5040
2.General:
The figure in the tray instruction label has been embossed directly in the cassette, and in accordance with this change the tray instruction label has been discontinued. This action has been carried out as a measure to improve productivity.
3.Action:
From the 1st lot of 1998 August production.
Current parts Ref. No. Model name Version P/G No. Parts code 30 -4 TLABZ3105FCZZ AR-5132 All 48 -4 48 -18 GCASP0156FCZ2
New parts Parts code Price rank Parts name
Effec- Intertive changeability time
Note
Discontinued
----
Tray instruction label
GCASP0156FCZ3
BB
Tray drawer case Tray instruction label Tray drawer case
1st lot '98/8
5
44 -4 AR-5040 44 -18 1. Interchangeable.
TLABZ3105FCZZ
Discontinued
----
GCASP0156FCZ2
GCASP0156FCZ3
BB
4. Not interchangeable. 5. Interchangea |
are182.pdf | | Date : Oct. 5, 1999 Digital Multi Function Copier: AR-5130/5132 No. : ARE-182
1. Simulation setting change due to addition of decurler mechanism 2. Assignment of parts code for ST upper P/G sheet guide jig ass'y
1. Simulation setting change due to addition of decurler mechanism
1. Model Name
AR-5125 (except Europe) 5130/5132 AR-5122F/FR/5230F/FR/5030F/FR (* For the SF-2530 (except SEC), SF-2540 (except SEC/SECL) and AR-5125 (for SEEG, SUK and SCA), it has been executed from the 1st unit of mass production.)
2. General
Since the decurler mechanism is added (in the market), the simulation setting value is changed. (1)About the measures when mounting the decurler kit in the market When mounting the decurler mechanism to each machine, change the value of SIMULATION 52-3 (ADU drive clutch OFF time setting) to the following numerical value.
Model name SF2022 SF2027 SF2035 SF1125 SF2025 SF2025N SF2030 SF2030N SF2040 SF2040N SF2530 All destinations All destinations All destinations All d |
are186.PDF | | Date : Nov. 8, 1999
DIGITAL COPIER(OPTION): AR-5132,SF-D23
No. : ARE-186
CHANGE CARRIED OUT IN THE CASTERS OF THE DESK UNIT.
1.Model Name:
AR-5132, SF-D23
2.General:
A change has been carried out in the casters. This action has been carried out as a measure to use up the stock of changed casters-100S which were described in Technical Report ARE-97. Please note that a change is also scheduled for the casters-100 after the stock of casters-100S have been completely used up.
3.Description:
Part name Caster 100S Caster 100 Part code 0CW4051P385// 0CW4051P384// Quantity 2 42
4.Action:
From 1999 September production.
Current parts Ref. No. Model name Version P/G No. Parts code 40 -18 All SF-D23 (SF-2040) 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. 55 -18 ----
New parts Parts code Price rank Par |
are200.PDF | | Date : Nov. 12, 1999
DIGITAL COPIER: AR-5125
No. : ARE-200
[Service Information]
CORRECTIONS CARRIED OUT IN THE PARTS GUIDE.
1.Model Name:
AR-5125
2.General:
There was an error found in the parts guide for the model listed above. The error has been corrected and is hereby reported.
3.Description:
Parts list: [2] Operational Panel
Error
HINDP0535FC10 HINDP0535FC11 HINDP0535FC12 23 HINDP0535FC13 HINDP0535FC14 HINDP0535FC15 HINDP0535FC16 Key sheet A English Key sheet A Germany Key sheet A French Key sheet A Spain Key sheet A Italy Key sheet A Netherlands Key sheet A Sweden
Corrected
HINDP0535FCZ3 HINDP0535FCZ4 HINDP0535FCZ5 HINDP0535FCZ6 HINDP0535FCZ7 HINDP0535FCZ8 HINDP0535FCZ9 AR AR AR AR AR AR AR
HINDP0537FC10 HINDP0537FC11 HINDP0537FC12 26 HINDP0537FC13 HINDP0537FC14 HINDP0537FC15 HINDP0537FC16
Key sheet C English Key sheet C Germany Key sheet C French Key sheet C Spain Key sheet C Italy Key sheet C Netherlands Key sheet C Sweden
HINDP0537FCZ3 HINDP0537FCZ4 HINDP0537FCZ5 |
are250r.pdf | | Date : Oct. 27, 2000 DIGITAL COPIER (OPTION): AR-CL1/CL2/5040 etc. No. : ARE-250R
Technical Report
SUPPLY OF PAPER FEEDING ROLLER RUBBERS AS SEPARATE SERVICE PACKAGES.
1.Model Name:
AR-5040/5125/5132/CL1/CL2 Technical Report No. ARE-250, which was previously issued, has been revised and is hereby issued once again. There were some unnecessary parts listed in the table of parts presented in the "General" section of the technical report. The error has been corrected and this technical report has been issued once again as No. ARE-250 (Revised).
2.General:
Up to now we have supplied roller rubbers for different types of rollers--paper feeding rollers, reversing rollers, guide rollers and hand-feeding guide rollers--in sets with roller shafts. However, in response to requests from the market, we will now issue service codes for roller rubbers and make them available as separate service packages. One service package will contain 10 roller rubbers.
Part codes for service packages of roll |
S211.PDF | | Date : Aug. 1, 1997
DIGITAL COPIER : AR-5132
No. : S-211
[Service Information]
1.DISCONTINUANCE OF THE PLUG CAUTION LABEL. 2.ADDITION OF THE BSI KITE MARK LABEL.
1. Discontinuance of the plug caution label.
1.Model Name:
AR-5132 (only for machines bound for the U.K.)
2.General:
The plug caution label which had been attached to the AC cord in machines bound for the U.K. market has been discontinued. This change has been carried out in accordance with a directive from the U.K. market.
3.Action:
From the 1st lot of 1997 July production. 2. Addition of the BSI kite mark label.
1.Model Name:
AR-5132 (only for machines bound for the U.K.)
2.General:
Akite mark label has been attached to the left upper side of the left cabinet. This change has been carried out in accordance with the BSI standards. Note: The kite mark label is a standard label, and has therefore not been established as a service part.
3.Action:
From 1997 mid-June production.
Current parts Ref. No. Model name Ver |
S230.PDF | | Date : May. 15, 1998
DIGITAL COPIER : AR-5132
No. : S-230
CHANGE IN THE FUSING MAIN HARNESS CARRIED OUT IN THE FUSING UNIT.
1.Model Name:
AR-5132 (only machines in the 200 V series)
2.General:
Achange has been carried out in the fusing main harness. This action has been carried out as a measure to make further enhancement safety performance in the electric circuits of the fusing unit.
Fusing main harness DHAI-2781FCZZ
DHAI-2960FCZZ
3.Action:
From 1998 mid-February production.
Current parts Ref. No. Model name Version P/G No. Parts code
New parts Parts code Price rank AW Parts name
Effec- Intertive changeability time Mid'98/2
Note
AR-5132 200V series 1. Interchangeable.
16 -62
DHAI-2781FCZZ
DHAI-2960FCZZ
Fusing main harness (EX200V)
3
4. Not interchangeable. 5. Interchangeable if replaced with same types of related parts in use. 6. Others.
2. Current type can be used in place of new type. New type cannot be used in place of cu |
SP2131.PDF | | Date : May. 16, 1997 DM11/AR-5132 No. : SP-2131
MEASURE TO PREVENT RETURN ROLLER CONTACT.
1.Model Name:
SF-DM11
2.General:
There were problems of the transport P guide upper of the ADU coming in contact with the return roller in the models listed above, caused by looseness. As a measure to alleviate this problem, tighteners have been added in two locations on the roller section of the transport P guide.
3.Description:
Transport PG upper AS
(Old) CGIDH1360FC01 (New) CGIDH1360FC02
4.Action:
From the start of 1997 March production. (Temporary action has already been carried out during production for the period between mid-January production and February production.)
Current parts Ref. No. Model name Version P/G No. Parts code
New parts Parts code Price rank Parts name
Effec- Intertive changetime ability
Note
SF-DM11 (SF-2022) 1
All
43 -66 Transport P guide upper AS 1st lot '97/3
SF-DM11 (SF-2025) Overseas 41 -66 (SF-2030) SF-DM11 (SF-2040) 1. Interchangeabl |
ste014.PDF | | Date : Feb. 23, 1998
COPIER : AR-5132
No. : STE-014
REGARDING MODIFICA TION OF PARTS CODES DUE TO CHANGE OF PROVIDER.
1.Model Name:
AR-5132
2.General:
Because the factory for manufacturing developer units and toner hopper units has changed, we have modified parts codes.
3.Action:
From December, 1997 production on.
Current parts Ref. No. Model name Version P/G No. Parts code All AR-5132 Inch series 14 -901 AB series 1. Interchangeable. 2. Current type can be used in place of new type. New type cannot be used in place of current type. 3. Current type cannot be used in place of new type. New type can be used in place of current type. CBOX-0105FC56 15 -901 CBOX-0104FC55 CBOX-0105FC55
New parts Parts code CBOX-0104FCE5 CBOX-0105FCE5 BL CBOX-0105FCE6 Toner hopper A unit (AB series) Price rank BW Parts name
Effec- Intertive changeability time
Note
Developer unit Toner hopper B unit (inch series) '97/12 1
4. Not interchangeable. 5. Interchangeable if replaced with s |
STE021.PDF | | Date : Sep. 28, 1998
COPIER : AR-5132
No. : STE-021
CHANGE CARRIED OUT IN THE MATERIAL OF THE MIXING ROLLER BEARING IN THE DEVELOPING TANK.
1.Model Name:
AR-5132
2.General:
A change has been carried out in the material of the mixing oil-roller bearing (Teflon) used in the developing unit. This action has been carried out as a measure to improve reliability concerning the bearing. The new bearing has a higher oil retention performance (Material name: PCA04)
3.Description:
A change has been carried out in the material of the mixing roller bearing of the developing unit. Bearing ø5 Teflon ø5 Bearing EX NBRGC0570FCZZ NBRGC0597FCZZ
1/2
Yellow C
SHARP CORPORATION
Printing and Reprographic Supplies Division
4.Interchangeability:
New parts can be used in place of old ones, but old parts cannot be used in place of new ones. [How to distinguish between parts.]
Hole
(ø5 bearing EX) * Old parts have no holes.
5.Action:
From 1998 May production. [Developing tank serial No.]
Month |